Jump to content
SAU Community

Recommended Posts

that grey s14 actually sits very well however only the 1 crap photo was posted if u check it out on hellaflush.com it looks quite good but s14s have a crappy rear bar and make it looks like dogs balls. Luke ur fitment is good but geeze sir you could hide a boeing 747 under your car..

P1170004.jpg

P1170003.jpg

P1170008.jpg

not the best pics but all wheels are inline rear runs a fair bit of camber to tuck the top in but 18x10 +20 fits nicely i still have enough traction tyre stretching is not as bad as suggested above within reason. i'd go lower but at 70mm off the ground not much room to move already kinda hard to drive around :banana:

  • Replies 230
  • Created
  • Last Reply

Top Posters In This Topic

My fitment:

my350z_20070929_nightshots_09.jpg

It's as flush as I can get with the stock camber/unrolled guards. However, I am still running a decent tyre size (255 front, 285 rear) and even on the track at full lateral load I don't touch.

I'd like the car to sit lower, but in Sydney that's not an option if I want to keep my lower bodywork intact.

i like 350z got any more picks?

http://www.au-z.org/gallery2/v/my350z/?g2_page=2

Look at the pics after 2007-08-01 - my 17" TE37s were a bit of an embarrassment.

For other 350Zs I've taken pics of, check here.

carpark pics are tough with the graffiti etc was that actually in melb?

Yeah, but I've heard they've demolished that carpark now.

Melbourne has the best graf, at least in locations that are easily car accessible.

your car is tough as i say lower it will set it off soo much bit of under scraping is ok :banana:

I have to get mega angle at 1km/hr up my driveway right now to get it into the garage. I have a rule that I should always be able to get my car into my home without damaging the car.

If I move to a location in Sydney that has reasonable driveways and no speed humps, or down to Melbourne, I'll probably drop it half an inch. But, right now, my car is as low as it can go where scraping the front lip/undercarriage is only occasional.

isnt that mexican. just the angle of the shot. Was just toying around with a 20mm spacer. 18x10 -2

heres one with 18x10 +18. 235/40/18

that looks phat!!!!!!!!!!!

love the black and white combination

but it must be hard keeping that baby clean :down:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...