Jump to content
SAU Community

Recommended Posts

  • Replies 846
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey Luke

Just wired through $200 to the account mate.

Description - Krishy Track Day

You guys should be able to get it by tomorrow.

Ruby can you please check that tomorrow and let me know via a PM.

Thanks

Krishy

what track pads should i buy for the 33 GTST? want to use em on the road too, have previously used s tune pads

Hey cosi mate i got QFM A1RM and they will do fine for both street and a bit of track work......you will also find a lot of people on here are using them....i paid $238 del for all 4 sets....of GSLrallysport (not too sure of the username) on here.....go back afew pages on here and you will find a link to him.....i just PMed him and customer service is very good

Hey cosi mate i got QFM A1RM and they will do fine for both street and a bit of track work......you will also find a lot of people on here are using them....i paid $238 del for all 4 sets....of GSLrallysport (not too sure of the username) on here.....go back afew pages on here and you will find a link to him.....i just PMed him and customer service is very good

Fair enough Krishy. Have you used these pads at the track before though? or has anyone? whats the brake fade like?

Congratulations to David (writeoff) for winning the track day raffle. He will now participate at the low cost of $5. Mind boggling as to why more tickets didnt sell, even to those who had already paid and/or entered, surely the $5 gamble is worth saving hundreds.

Again, Congrats David from the exec :cheers:

Thanks Damo.

Congrats David have fun :D

Thanks Steve - it was the early positioning on the sim that resulted in the ticket being bought when it was. I was so hot after my run that I needed a drink. Only had a tenna so said that I'd grab a ticket as well. Worked out rather well for me :cool: and makes up for my poor times on the sim (although they would have been better if I hit the brake pedal instead of the clutch pedal).

want a spot... booked the day off :cool:

Speak to the execs as there was a spot reserved for the winning raffle ticket and I already had a place and had paid for it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...