Jump to content
SAU Community

Recommended Posts

honestly I would probably rate the old a048s over the 888s with one downside that the a048 does go off after fewer heat cycles, but it's outright pace is better than the 888. the new A050 is miles better though.

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

595RSR is priced between r-comps and streets, and it sits where all the other street cross track tyres sit in terms of price and performance.

KU36 can't be beat for the price but I don't understand when people say stuff like "If I'm paying double the price of KU36 for X or Y tyre then they better be double the performance!" There's not much that I can think of when talking about performance, where you get double the goodness for double the price - it doesn't work that way unfortunately.

honestly I would probably rate the old a048s over the 888s with one downside that the a048 does go off after fewer heat cycles, but it's outright pace is better than the 888. the new A050 is miles better though.

It's the heat cycling that rates them lower for me. They are fine at the start of their life but rubbish after a few days where as the r888 is slower but more consistent for it's life.

Yeah, all the a050 feedback i've seen is positive.

for what it's worth, if you are even half serious you are wasting your time with anything but the best tyres.

when you are on the track are you competing (eg supersprint)? or running a lap timer?

top line semi slicks like re55s or dz03 will give you at least 1 second a lap over falken rsr/kumho ku36. second tier semis like kumho v70 or toyo 888 or yoko a048 will be at least 1/2 sec faster.

If cost is an issue (it always is lol) the v70 kumhos are a good choice at about 1300 va set in 245/40/17.

even better if you want to save money - run the smallest diameter wheel you can fit over the brakes. 17s are about 30% cheaper than 18s and 16s are cheaper again. the stiffer sidewall of semi slick tyres minimises or eliminates any disadvantage from the higher sidewall.

Dunc - since you menetioned v70s where do you get them from? FR sport? and how did you rate the khumo slicks you were on at OP?

MRA gives the option of slicks or treaded so depending on price id prefer the slicks.

you can pm me if you want

yeah talk to John at F-sport. Tell him I sent you and he will add 10% to the price lol. At 1300 a set they are half the price of dunlops in the same size, so if 1/2 sec doesn't matter for what you are doing they are a bargain.

At Oran Park I had kumho slicks on the front and falken slicks on the rear (same size). They were f**king excellent. For example I was taking Suttons in 4th which i have never even considered on semis. Literally 10-20% faster in a corner so 1-2sec for a whole lap.

When slicks are an option they can be cheaper too because they might last longer (up front cost may be say 20% higher but if they keep their performance 50% longer....). But you would still need either semis for bad weather or be willing to park it...makes for a difficult decision because everyone I know who has wet tyres never uses the things which makes slicks an expensive option.

slicks worked well for me because I normally have to use semis, so I had a few I could drag along in case it rained (which it didn't in this case, despite the forecast)

The rain issue has me a bit doubtfull, as i only have 1 set of rims atm, I dare say I would park it in the wet, unless i buy a cheap set of factory rims and throw some KU36's on them for wet days / practice days

teh slicks should put me (in theory) in the 1:08s easily at wakefield which is right up the front of the current MRA field so for a bit more money it might just be worth it.

yeah...also if it is only a single race meet then slicks aren't such a big gamble.

with stuff like the state champs though you need to score well every round, so you just can't risk having to sit out a whole round from a points persepective

How do the V70's compare to the RE55's?
....top line semi slicks like re55s or dz03 will give you at least 1 second a lap over falken rsr/kumho ku36. second tier semis like kumho v70 or toyo 888 or yoko a048 will be at least 1/2 sec faster.....

my opinion only....but i have seen them compared in very similar circumstances

595RSR is priced between r-comps and streets, and it sits where all the other street cross track tyres sit in terms of price and performance.

KU36 can't be beat for the price but I don't understand when people say stuff like "If I'm paying double the price of KU36 for X or Y tyre then they better be double the performance!" There's not much that I can think of when talking about performance, where you get double the goodness for double the price - it doesn't work that way unfortunately.

last time I priced Federals they were almost exactly the same as what I got quoted for Toyo R888 and RE55S. Up around $330 per tyre in 235/45*17

You can get tyres that perform almost exactly the same as the RSR for almost exactly half the money.

OR you can get tyres for exactly the same money as the RSR that will run rings around them.

understand?

You're shopping at the wrong place Harry. any time you want feddy's in the rsr guise let me know.

The feddy's are not the best semi on the market, Nor do they claim to be.

they do offer outstanding value for money for those looking for one tyre to do it all. They are a competent track tyre and an outstanding street tyre for a high performance ride. The Khumo's are probably similar but from what i have seen the feddy will go a lot further than the khumo.

I've run sub minute on qr sprint using the rsr and still get good mileage from them on a daily usage deal.

The best they are not. The best value they most certainly are IMO.

last time I priced Federals they were almost exactly the same as what I got quoted for Toyo R888 and RE55S. Up around $330 per tyre in 235/45*17

Where from? Most of the prices I've seen for 17" RE55S have been at least $400 each (RRP is over $538). If I could get them for $330 each I'd be pretty stoked.

last time I priced Federals they were almost exactly the same as what I got quoted for Toyo R888 and RE55S. Up around $330 per tyre in 235/45*17

You can get tyres that perform almost exactly the same as the RSR for almost exactly half the money.

OR you can get tyres for exactly the same money as the RSR that will run rings around them.

understand?

You're paying too much for RSRs.

Those R888's are grey imported, try price the proper current australian stock australian compounds.

RE55S in 235/45/17 for $330each? No chance, not even close.

You need to do a bit more homework :)

Edited by _Wing_
for what it's worth, if you are even half serious you are wasting your time with anything but the best tyres.

when you are on the track are you competing (eg supersprint)? or running a lap timer?

top line semi slicks like re55s or dz03 will give you at least 1 second a lap over falken rsr/kumho ku36. second tier semis like kumho v70 or toyo 888 or yoko a048 will be at least 1/2 sec faster.

If cost is an issue (it always is lol) the v70 kumhos are a good choice at about 1300 va set in 245/40/17.

even better if you want to save money - run the smallest diameter wheel you can fit over the brakes. 17s are about 30% cheaper than 18s and 16s are cheaper again. the stiffer sidewall of semi slick tyres minimises or eliminates any disadvantage from the higher sidewall.

It's for supersprinting. Went cheap ones because there's still a few more parts that I need to get relatively soon. I would have liked to gave gone the RE55's but the rears alone were about $500 (for 255/40/17). Next time it comes to upgrade I'll fork out for proper semi's.

With what you were saying with the RE55's and 888's; one of the guys in the wrx club tested both of them back to back at EC. The RE55's were just over a bit over a second a lap quicker.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...