Jump to content
SAU Community

Unsure What Is The Problem With My Rb25

fat_stag

By fat_stag,
in Engines & Forced Induction

 Share

Recommended Posts

fat_stag Collaborator

fat_stag

Posted
Posted (edited)

hey guys im havin some problems diagnosing whats causing my car to play up.

ill list what is happening and what i have checked.

problems: constant whit/blue somke out the exhaust.

wont hold/make max boost

miss firing

motor fluds with oil when gets hot.

when i took the intake pipe off the turbo there was oil all over the inside all the way to the pod filter

goes through alot of oil.

things i have checked: no shaft play in turbo

just disconnected the oil catch can and put it back to standard to check.

called hypergear to ask about it all and they suggested the the catch can bisso because of the turbo not havin shaft play so they dont think its a oil seal but thats what the previous owner said it was.

the turbo is a garret t04 hyflowed with bigger wheels.

would be much appreciated for a few suggestions to try out. cheers guys

Edited by fat_stag
hypergear Grand Master

hypergear

Posted
Posted

Well. I don't felt the right to charge you $440 to replace some thing that doesn't require to be done.

Your engine's leaking oil all over the places not just the turbo.

So get you engine oil, catch can and all other issues fixed fist. We will have a look at your turbo if its still making blue smoke by then.

PM-R33 Grand Master

PM-R33

Posted
Posted

Can you elaborate on "motor fluds with oil when gets hot". What do you exactly mean by this? What oil is in the vehicle and when did this start happening? Did you do something the last few days before this started happening?

GTScotT Grand Master

GTScotT

Posted
Posted

how did you install the catch can?

once had a perfectly good turbo shit a seal because a catch can got installed with no breather, 2 outlets on the rockers to 2 inlets on the catch can and no breather anywhere lol... insta-goodbye T28BB :)

was there a way for your catch can setup to breathe properly? or have you made a similar faux pas

hypergear Grand Master

hypergear

Posted
Posted

Well once you clear breathers and fix other issues to allow oil drain back into the sump, the turbo will stop smoking.

In most of cases If the turbo's got no shaft play and leak oil through both seals its means there is a oil drainage problem. Once fixed the turbo stops smoke. No need to pay $$$ and overhaul a good turbo.

GTScotT Grand Master

GTScotT

Posted
Posted

in my case the catch can was only connected wrong for a total of 30 seconds, and the car would drop its sump out the exhaust from milperra to ramsgate it was spewing out oil so bad... irreversable damage to the seals.

this could be the case here, yet yes agreed with hypergear, trial and error try fix whats blocking up if there is and go from there.

gotRICE? Veteran

gotRICE?

Posted
Posted

Is your PCV blocked by chance?

I had a smoke issue with my RB25 when i had it set up with a blocked PCV valve catch can setup.

Put the stock PCV valve back in, and it went away and never came back.

Only issue is being at idle i can occasionally get rev fluctuation due to the atmo venting breathers.

(because the pvc is connected and gets a bit of un AFM'd air via the breathers :) )

fat_stag Collaborator

fat_stag

Posted
  • Author
Posted (edited)

yea cheers guys for the tips and sorry stao i hope you didnt take any of this as badmouthing you i was just sayin what ya said and what my mate said. yea i also couldnt hear ya propperly over the phone because i had shit service and a bit of wind around me. will check all the lines from turbo for blockage's and might just get a new catch can to eliminate that as i issue but the one i got has a breather. also ill get onto a compresion test to see how that is. who knows could also be sparkplugs gunked up from having oil goin through there thats causing the missing. thanks heaps again for the help and ill be in contact with ya stao if all this dont work.

Edited by fat_stag
zebra Grand Master

zebra

Posted
Posted
have you done a compression test? I think you've got a busted ring land.

I am in agreeance with you there..

if you can pull the turbo off...if the exhaust manifold is full off sludge then its rebuild time. or the easier way would be to get a comp and leak-down test done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...