Jump to content
SAU Community

Recommended Posts

So, I got my whiteline rear sway bar put on today, along with my Kumho KU36s on the front and full suspension check/alignment. My whole suspension was apparently all over the place, with a lot of negative camber on both wheels.

Anyway, since getting the car back, the car feels... good. I suspect this is the proper alignment making the a car much nice driver, however I have concerned about the sway bar. When cornering, not even when cornering hard, it feels like the rear really wants to kick out.

When coming out of a round about I gave the car a little prod and I felt the rear lose traction slightly.

My question is, is this normal? Will I just have to get used to this new driving style, or is the rear bar a little too stiff perhaps? I was told it would help combat the under steer in my nose heavy Supra, but I feel less comfortable cornering now that I did before.

I'm quite the novice when it comes to suspension (although I am learning!), so I'd appreciate any feedback.

Cheers,

Kieran.

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/
Share on other sites

Quick update, took the car for a bit of a spirited drive today and it handles really, really well.

It feels like it wants to let go (or at least when the car felt this way prior to the changes it was going to let go), but it just grips and goes. I guess I have to relearn the car and its limits, might wait till DECA before I really start pushing it though.

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/#findComment-5052033
Share on other sites

  • 2 months later...

so does that mean that upgraded front swaybar only, will cause understeer?

and how about the balance of stiffness between upgraged front and rear, on r33 in particular? 24mm front + 22mm rear. will it tend towards understeer?

or will the rear end (being much lighter) have less roll than the front, regardless? ie. tend towards oversteer

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/#findComment-5177812
Share on other sites

so does that mean that upgraded front swaybar only, will cause understeer?

Yeah, or more correctly shift the bias of the car from oversteer to understeer. If you stiffen up one end, the tyres at that end will work harder and therefore loose grip earlier relative to the other end.

and how about the balance of stiffness between upgraged front and rear, on r33 in particular? 24mm front + 22mm rear. will it tend towards understeer?

or will the rear end (being much lighter) have less roll than the front, regardless? ie. tend towards oversteer

There's more to it than the diameter of the bar - the length of the arms also determines how the bar flexes - think of what happens with a longer bar when you're undoing a nut. That's why the outer connections on an adjustable bar make it less stiff. WRT weight - the heavier end will work the tyres harder, so you can compensate for that by putting more bar on the other end.

IMO its best to replace both front and rear at the same time and get at least one adjustable so you can play with understeer/oversteer balance. If you're going to track it adjustables both ends.

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/#findComment-5178102
Share on other sites

good info :)

so what have people generally found on 33gtst for street with the 24mm adjustable front + 22mm fixed rear? which adjustment works best at the front?

so settings are like so. ie. more leverage, less resistance. makes sense

20070505_2885.JPG

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/#findComment-5178154
Share on other sites

so what have people generally found on 33gtst for street with the 24mm adjustable front + 22mm fixed rear? which adjustment works best at the front?

Each car will be different (tyres/wheels, alignment settings) so just try the middle setting first for a bit and see how you like it. Trackday would be safest to try out different settings.

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/#findComment-5178211
Share on other sites

IV had an adjustable front swaybar sitting in the boot of my R33 for over a year now still in its packaging.. wonder how well its working :D

But in all seriousness, i was going to wait till i got the rear to install it, and just never got it. Was going to put it in soon, but the general consensus is that i should get a rear one and do both at the same time yes?

Interesting the rears are quite a bit more than the fronts. Ideas?

Link to comment
https://www.sau.com.au/forums/topic/304939-rear-swaybar/#findComment-5180061
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...