Jump to content
SAU Community

Recommended Posts

Hi guys

Im wrecking a 1997 Model R33 GTR Series II which i have just bought, the parts will be available in one month and the car has travelled 30,000kms and pretty much stock except for wheels and exhaust etc etc. [email protected]

Car is located in Sydney, willing to arrange freight at buyers expense for any parts

NB ** IF YOU ARE INTERESTED IN ANY PARTS PLEASE MAKE A LIST AND EMAIL THEM TO [email protected] NO REPLIES IN THIS POST WILL BE REPLIED TO REGARDING PRICE ETC **

Jordan

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/30648-wrecking-series-ii-97-r33-gtr/
Share on other sites

Hi Guys

Had a few people asking about parts here is a short list of what is available:

** Engine

** ECU

** AFMS's

** Gearbox

** Diff

** Front Seats

** Rear Seat

** Rear Wing

** Fuel Pump

** Radiator

** Intercooler

Please keep in mind that the car is only 30,000kms old and a 97 model so be ready to pay accordingly

Jordan [email protected]

Hi Guys

Had a few people asking about parts here is a short list of what is available:

** Engine $9000 complete with ecu, harness and afm's

** Gearbox $3000 complete with clutch and flywheel

** Diff $1000

** Interior (minus dash and center console) $3000

** Rear Wing $500

** Fuel Pump $400

** Radiator $200

** Intercooler $700

Please keep in mind that the car is only 30,000kms old and a 97 model so be ready to pay accordingly

Jordan [email protected]

  • 1 month later...
Hi guys

Im wrecking a 1997 Model R33 GTR Series II which i have just bought, the parts will be available in one month and the car has travelled 30,000kms and pretty much stock except for wheels and exhaust etc etc. [email protected]

Have you still got those seats at all, and how much ??

Hey descr8,

would you be able to pull off the panelling inside the wheel wells at the front? (the black stuff with the vents) mine are worn down, need to replace. It goes onto a s1 gtst, so let me know if it can be done...thanks man

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...