Jump to content
SAU Community

Recommended Posts

You can also look into putting steel wheels into your turbos, if its a tight budget and only looking at slight performance. I'm running 17psi on my ones and 287rwkw with supporting mods and it cost me $1100 with all the labour done myself, I bought the turbo cores of a member here with the wheels already balanced and ready to go and just added my exhaust housing and compressor housing of the old turbos. Not that hard if you have basic mechanical knowledge, I had no issues doing all this myself and saved alot on labour.

But if budget allows, do what R31Nismoid recommended earlier Garrett -7, much better than my option and can make much more power as well as less work involved.

Cheers

Aren't the -9's the way to go now instead of -7's? (or are they more expensive?)

Well Nismoids above post has thrown me as for the past few months I have noticed he is a pro -9 man :P

Edited by gtr fan

i can vouch for garretts being the best choice for a street replacement on a budget.

i would say go the -7's or -9's

i've got -5's which are a little bit of overkill, i only got them because they were the ones that came available the soonest when my stockers blew the rear wheel off.

the -7's or -9's would be better for response and still have plenty of power!

i hope your mates car will be fine after he gets the turbo's replaced and doesnt have my luck and have the motor blow a week and a half after the new turbos are installed.

Aren't the -9's the way to go now instead of -7's? (or are they more expensive?)

His post says slight improvement over factory, -7's are the closest.

-9's are 330rwkw, which IMO i wouldn't be taking a R32 motor to that level given their age/conditoon now.

So 280rwkw or so on -7's would be reasonable and about 30-40rwkw more than factory turbo's.

If he wanted a bit more performance, with a planned rebuild, then -9's for sure.

Say you were running 300kw, would the -9s produce that with a slightly lower temperature (due to the better compressor efficiency) than the -7s? Or are they only better when you're running them right at the peak?

Not 100% sure but it's not going to be a 30 degree difference or anything major i would imagine.

Probably a difference, however majorly signifigant? Probably not.

300rwkw i would still pick -9's though. 280rwkw would be the aim for -7's.

just a slightly off topic question....why are the power out puts between a -7 and a -9 so different, looking at the spec sheets they are so close to the same it isnt funny (-9 slightly smaller in the compressor and slightly larger in the turbine but we are talking 0.0Xmm difference)

Rebuild it with steel internals or go for R34 GTR N1 turbo's.

Or any aftermarket that is listed in thread.

what is the benefit of N1 turbos , everybody says there great , what would a pair set me back!

what is the benefit of N1 turbos , everybody says there great , what would a pair set me back!

They came from factory on the R34 GTR V-Spec II N1, R34 GTR V-Spec II Nur and R34 GTR M-Spec Nur.

R34 GTR N1 turbos came from factory with steel internals and they ran 1.2 bar boost stock.

So they are very strong and responsive.

I had driven a R34 GTR V-Spec II Nur with 306 rw kW's still retaining the N1 turbos.

Was excellent.

Try the for sale section and from memory about $1450 + a pair.

- http://www.skylinesaustralia.com/forums/Wr...mp;hl=n1+turbos <--- He's selling them for $1450 a pair.

Should be straight bolt on fit too.

They came from factory on the R34 GTR V-Spec II N1, R34 GTR V-Spec II Nur and R34 GTR M-Spec Nur.

R34 GTR N1 turbos came from factory with steel internals and they ran 1.2 bar boost stock.

So they are very strong and responsive.

I had driven a R34 GTR V-Spec II Nur with 306 rw kW's still retaining the N1 turbos.

Was excellent.

Try the for sale section and from memory about $1450 + a pair.

- http://www.skylinesaustralia.com/forums/Wr...mp;hl=n1+turbos <--- He's selling them for $1450 a pair.

After reading a few topics and the GCG website the gt2860r-7 are equalent or closest to n1 turbos that came in the cars that you mentioned.

My understanding is that the gt2860r-9 are equalent or closest to HKS GTSS.

just a slightly off topic question....why are the power out puts between a -7 and a -9 so different, looking at the spec sheets they are so close to the same it isnt funny (-9 slightly smaller in the compressor and slightly larger in the turbine but we are talking 0.0Xmm difference)

The physical dimensions of the wheels are one of MANY variables. The -9's have newer more modern wheels which flow more and more efficiently without needing to be bigger or lighter.

To the previous posts about the -7 turbos, I'll say it again, -9's AREN'T any laggier than -7's so there is NO advantage of -7's! If u only want to make a certain amount of power, just run -9's on low boost!

i can vouch for garretts being the best choice for a street replacement on a budget.

i would say go the -7's or -9's

i've got -5's which are a little bit of overkill, i only got them because they were the ones that came available the soonest when my stockers blew the rear wheel off.

the -7's or -9's would be better for response and still have plenty of power!

i hope your mates car will be fine after he gets the turbo's replaced and doesnt have my luck and have the motor blow a week and a half after the new turbos are installed.

Damn that is bad luck

Im guessing the ceramic turbos did the damage initially.

I was thinking the way to go is gt2860r-7

Are bigger turbs generally more laggy.

Everyones advice has been extremely helpful .

Damn that is bad luck

Im guessing the ceramic turbos did the damage initially.

I was thinking the way to go is gt2860r-7

Are bigger turbs generally more laggy.

Everyones advice has been extremely helpful .

why not -9's? Newer more modern turbo. Same response, more efficient, more power, same price. I dunno why they don't discontinue -7's and put an end to all this confusion.

After reading a few topics and the GCG website the gt2860r-7 are equalent or closest to n1 turbos that came in the cars that you mentioned.

My understanding is that the gt2860r-9 are equalent or closest to HKS GTSS.

Yeah, I think your right, by looking at my Turbo Chart, the specs seem the same.

And yes the -9's = HKS GT-SS (well, very close)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...