Jump to content
SAU Community

About To Buy My New Baby - Very Excited !


Recommended Posts

Hi Guys,

Great to see this forum is still going strong.

Been a while since Ive been on it (my old username was jezzrrr) since sold both my R33 GTR & R34GTR VSpec.

Now looking for a used R35 weapon and very excited about the prospect.

Will be doing some immediate mods like:

exhaust

brakes

tyres

cobb or similar tune

My objective is to unlock the beast and have a reliable track/rally/road car.

What do you guys suggest in terms of specific mods in line with above e.g. brand etc and what sort of costs will I be looking at ?

p.s. "the Law" not a cop - a lawyer.

Edited by The Law
Hi Guys,

Great to see this forum is still going strong.

Been a while since Ive been on it (my old username was jezzrrr) since sold both my R33 GTR & R34GTR VSpec.

Now looking for a used R35 weapon and very excited about the prospect.

Will be doing some immediate mods like:

exhaust

brakes

tyres

cobb or similar tune

My objective is to unlock the beast and have a reliable track/rally/road car.

What do you guys suggest in terms of specific mods in line with above e.g. brand etc and what sort of costs will I be looking at ?

p.s. "the Law" not a cop - a lawyer.

I went for HKS570 kit, 800cc injectors, Cobb custom tune, AP slotted rotors, Carbotech 12 pads for track, Endless MX72s for street, stock back end exhaust, dunlop tyres. These mods are pretty basic really, but see 401kw at the wheels (check out the thread Love The Beast to see the results). I have two custom maps for street/drags & track. The car is incredibly reliable, but quite loud.

Cost wise expect to spend btw $20k and $30k. Jim at Croydon Racing Developments has done all my work ( and my last eleven cars!).

Hope this helps.

I went for HKS570 kit, 800cc injectors, Cobb custom tune, AP slotted rotors, Carbotech 12 pads for track, Endless MX72s for street, stock back end exhaust, dunlop tyres. These mods are pretty basic really, but see 401kw at the wheels (check out the thread Love The Beast to see the results). I have two custom maps for street/drags & track. The car is incredibly reliable, but quite loud.

Cost wise expect to spend btw $20k and $30k. Jim at Croydon Racing Developments has done all my work ( and my last eleven cars!).

Hope this helps.

Thanks great details.

Looked at your thread looks great, seemed like you got the 401KW without the 800cc injectors, were they necessary ?

Also whats the cost of the HKS 570 kit ? do you think its the way to go rather than just say a good mid pipe ??

Thanks great details.

Looked at your thread looks great, seemed like you got the 401KW without the 800cc injectors, were they necessary ?

Also whats the cost of the HKS 570 kit ? do you think its the way to go rather than just say a good mid pipe ??

Maybe guys like Martin could comment on this as well. The HKS 570 kit seems to have some unecessary bits in it. From what I've been able to see, the wastegate actuators and boost controller are not required with the latest Cobb accessport tunes. All it really has that would provide tangible value for money benefits are the midpipe and dump pipes. I'm not sure what real value comes from replacing the intake ducting with aluminium pipes and whether or not it requires bigger blow off valves. So would you be better off just buying the exhaust bits from Willall and/or others and then just going with the tune? (Their new titanium midpipe looks beautiful). And I'm also curious as to whether or not you needed to go to 800cc injectors when you were making 401 kW with the original ones? Was it just a safety decision as you were getting marginal on injector duty cycle?

Definitely +1 on the brakes and for wheels and tyres I'd go down the path of 18s with 2nd hand slicks as many on here have done for best value/speed for money. Depends on whether you want to trailer your car to the track or change them once there I suppose. I'm still a couple years away from doing my mods but always very interested in whats delivering the best results out there.

Edited by fungoolie

Yeah agreed the HKS570 kit is a very early kit and now has a few bits you wont need. You no longer need to touch the wastegate actuators or use any aftermarket EBC with the Cobb version 2.0 maps. Blow off valves are certainly just a gimmick. Provided you want to keep it mild you could opt for something else.

The stock injectors are pretty small and very easily maxed on stock turbos so it's no wonder he went larger.

Focus on the ECU tune (Cobb with either stock 2.0 maps or custom) and exhaust to give you a big smile when you put your foot down for relatively small investment.

I went for the HKS setup for a few reasons:

1. it was tested & proven at the time (Cobb wasnt even available)

2. it was an end to end kit from one manufacturer, I didnt want to mix parts (White 35 did this and there were all sorts of set up issues)

3. I want to do some serious mods down the track - turbos, intercoolers etc, hence I want to build a strong platform with the right hardware

The 800cc injectors are for two reasons -1. I wanted the safety as I was running out of injector with the stock ones, 2. again I have future fuel requirements in mind...

With the BOVs ,I've had history here - most factory BOVs I've used on Evos and WRXs leak under high pressure, it may seem excessive with the current setup, but when I crank this baby up they'll do the job (they look great too)

The HKS boost controller is incredibly flexible, enables me to change the power delivery without having to download a new map.

The full HKS setup cost me $12,500. Its incredibly consistent with the same power delivery every time. Pretty good value really.

So in summary I suppose it all depends on what your long term goals are - a mild tune is possible without all the hardware, but if your goal is to eventually build a low ten second car I reckon building the right hardware platform from the start is a must... whatever that hardware might be.

Looks like HKS are doing a 570 kit without the boost controller now but still providing the wastegate actuators as part of the kit. I can see the attraction of being able to change boost on the fly though. Fully understand your reasoning as to why you went for that kit when you did and considering what you have planned for the car.

A good mid priced turbo pipe kit is in the US$1000-$2000 range and a mid pipe AUS$900 and the accessport US$995 plus whatever the dyno costs are for a custom tune so if thats the full extent of your engine mods then all up you'll probably be looking at around the high $3000 range for the mid to higher 300KW range. Add another US$700 for injectors if required.

Edited by fungoolie

Great advice guys, thanks.

Think I will be going with a turbo back exhaust sytem like 09GTR's but will look at options incl but other than HKS too.

Will upgrade brake pads before 1st track day too having read the stories re cracked pads AND will get a set of Dunlops.

I can hear the beast scream in my dreams ....

p.s. who is the cheapest importers of parts to go with these days ?

Tyres you can get cheap direct from tire rack. ~$AU650 each landed dependent on exchange rate. Lots of good stuff available from Willall as well such as exhaust components.

For things like Cobb accessport, brakes etc, check sites such as gtrmod, speedforsale, forged performance and courtesy nissan (US) for maintenance items like air cleaners, oil filters, cabin filters, sump bolts/washers/gaskets .

Tyres you can get cheap direct from tire rack. ~$AU650 each landed dependent on exchange rate.

Sorry for the hijack, yet this may proove valuable anyhow.

I always ruled tirerack out as its a US site and assumed shipping would be more than the cost of the rubber itself. Can you give an indication of what shipping is worth from them?

Sorry for the hijack, yet this may proove valuable anyhow.

I always ruled tirerack out as its a US site and assumed shipping would be more than the cost of the rubber itself. Can you give an indication of what shipping is worth from them?

On certain tires, US price + shipping is still cheaper than any aussie price. Once Tempe and Taleb start parallel importing them though you should check them out locally before committing.

Sorry for the hijack, yet this may proove valuable anyhow.

I always ruled tirerack out as its a US site and assumed shipping would be more than the cost of the rubber itself. Can you give an indication of what shipping is worth from them?

Shipping's about US$240 for a set. I don't have the "luxury" of Taleb here in SA yet I'd still find it hard to believe they'd get you a set for $2600. Maybe I'm wrong. It only makes sense to buy OS when you are looking at expensive tyres though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...