Jump to content
SAU Community

Do Spacers Wreck Wheel Bearings?

Daz305
 Share

Recommended Posts

Daz305 Rising Star

Daz305

Posted
  • Author
Posted

yer i understand that moving the weight out puts more stress as they are further away. but does it actually wreck them...? and if it was only about 5mm would this make much of a difference? need to no some answers to help my decision on new wheels

suraido Contributor

suraido

Posted
Posted

5mm slip on's are not going to put that much more stress on the hubs.

Any spacer used should be hubcentric so the load is on the hub and not the wheel studs.

Going to a lower offset, especially -offsets can also cause a shorter life for wheel bearings. Same as a spacer.

Duncan Grand Master

Duncan

Posted
Posted

the only impact of a properly designed spacer is the increased load on the hub from leverage. And as said above that is exaclty the same as moving to a lower offset wheel.

much more important is "hubcentric". basically a wheel stud's job is to clamp the wheel to the hub, not locate it correctly. You must have a "hubcentric" fit between the wheel and the hub, this means that the wheel should be held in the right place by the hub not by the wheel studs. If you can put the wheel on without wheel nuts and rotate it a little it is not hubcentric.

basically a hub has a ring in the middle, and the wheel should be a tight fit on that. if you add a spacer it must fit snugly on the hub, and the wheel must be located on that as well. I have never seen a slip on spacer that has a hub ring to locate the wheel.

sh@un Grand Master

sh@un

Posted
Posted
basically a hub has a ring in the middle, and the wheel should be a tight fit on that. if you add a spacer it must fit snugly on the hub, and the wheel must be located on that as well. I have never seen a slip on spacer that has a hub ring to locate the wheel.

and that's why spacer rings are typically illegal

you don't wanna be losing a wheel after your studs shear through :D

Russman Grand Master

Russman

Posted
Posted
the only impact of a properly designed spacer is the increased load on the hub from leverage. And as said above that is exaclty the same as moving to a lower offset wheel.

much more important is "hubcentric". basically a wheel stud's job is to clamp the wheel to the hub, not locate it correctly. You must have a "hubcentric" fit between the wheel and the hub, this means that the wheel should be held in the right place by the hub not by the wheel studs. If you can put the wheel on without wheel nuts and rotate it a little it is not hubcentric.

basically a hub has a ring in the middle, and the wheel should be a tight fit on that. if you add a spacer it must fit snugly on the hub, and the wheel must be located on that as well. I have never seen a slip on spacer that has a hub ring to locate the wheel.

This is part of the reason I run nissan rims on the track (33 GTR). Even my very expensive ADVAN RS's are not hubcentric beacause they are generic fit. What are your thoughts on this duncan?

Also thinking about it. Having a +30 offset can't be much different to -30. Ideally a wheel with a 0 offset would be the best thing for bearing life. true?

Duncan Grand Master

Duncan

Posted
Posted

I guess having wheels at the centre of the car would reduce bearing load most, and having them hanging out would increase it the most....but perhaps the handling would suffer :D basically the extra load is just from the extra track width and the extra grip it brings...no magic to it.

having hubcentric wheels is really important for track use. It is easy to get hold of plastic locating rings once you have the hub diameter and wheel's inner diameter. Or like you said use the factory wheels 32/33/34 all locate correctly on the hub. With the current targa rules, r33 wheels are excellent for an r32

_Wing_ Proficient

_Wing_

Posted
Posted

Use metal hubcentric rings instead of plastic - plastic melts.

With +30 and -30 offset... -30 would have a much bigger load because of the extra arm length/leverage in relation to the turn.

Spacers/lower offset doesn't "wreck" bearings or sheer the studs themselves, but they certainly do put exponentially more load on them so you can expect a shorter service life.

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted
This is part of the reason I run nissan rims on the track (33 GTR). Even my very expensive ADVAN RS's are not hubcentric beacause they are generic fit. What are your thoughts on this duncan?

get some locating rings..... just need to measure the hub diamater and the wheels diamater and your set... bob jane et al stock them

Russman Grand Master

Russman

Posted
Posted
get some locating rings..... just need to measure the hub diamater and the wheels diamater and your set... bob jane et al stock them

Thanks for the info. I'll do that coz I didn't realise they were available. What are they generally made of? Alloy or steel?

  • 2 months later...
seanfontanini Explorer

seanfontanini

Posted
Posted

hey. i have a31 cefiro and have a set of r32 gtr rims. i have the hubs off a stock r32 with r32 gtr brakes. went to put the wheel on and the inner tyre wall is rubbing on my tiens. would spacers be the go in this situation. if so can anyone point me in the right direction of were i could get some. im in perth. cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...