Jump to content
SAU Community

R34 Air Cond. Air Filter Maint.

p75153

By p75153,
in General Maintenance

 Share

Recommended Posts

p75153 Rookie

p75153

Posted
Posted

The R34 has panel type filters in the air conditioning duct, between the fan and the evaporator.

I do have it with detailed pictures in a word doc, but it is too big for an attachment on this forum. Text only to follow...............

R34 Air Conditioning Air Filters:

SAFETY>>>>>>>>>>>All yellow wiring is related to the AirBag System. If necessary, disconnect battery before starting work

The R34 model has 2 panel-type air filters, to ensure clean air is passed through the evaporator coils. (I haven’t seen this feature on any other car before.)

Like any other filter, they also need to be cleaned, so here is some info that might make it easier next time. (It’s like brain surgery………….., easy….. when you know how.)

1. Remove the passengers-side sill trim (lever up with screwdriver, attached in 4 places)

2. Remove passengers-side kick-panel (unscrew plastic nut on firewall stud, and lever front edge off with screwdriver, attached in 2 places.)

3. Pull off rubber door sealing strip to top of dashboard.

4. Remove glovebox, by:

a. Removing the 2 lower hinge pins (by sliding inwards to unclip). Partially remove the glovebox lid, being careful not to break the tension string.

b. Remove the screw at the lower RHS of the glovebox assy, as shown below.

c. Remove 4 screws along the top edge of the glovebox.

d. Remove the screw at the lower LHS of the glovebox.

e. Disconnect the Glovebox-light cable, and remove the entire assy. The car should look like this now…

f. Remove the black spring clip on the lower edge of the white vertical filter cover, and gently lift the cover upwards.

g. Remove the 2 panel filters by sliding out the lower one first, and then the top one will fall down.

h. Remove the white fibre concertina element (dust filter), from both panels, gently clean with compressed air, then wash in hot water and detergent.

i. Remove the black honeycomb element (deodorising filter), from both panels, and very gently clean with compressed air only.

If you clean these elements carefully, they can be reused, as I would hate to think what a replacement filter would be worth.

The filters on my car were absolutely filthy…a fine specimen of the air quality in Tokyo I suppose!

Assemble parts in the reverse order, but pay particular attention to the alignment pin above the screw, on the lower RHS of the glovebox assy. See Fig 1 above.

As with all plastic parts on cars, don’t use excessive force to remove or replace them.

Hope this helps any fellow R34 owners.

Regards,

GK.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/30811-r34-air-cond-air-filter-maint/
Share on other sites
  • 2 months later...
666DAN Grand Master

666DAN

Posted
Posted

Yeah I did all this a little while ago when installing my e-manage.....which now resides on the vent covering the A/C....I only had little bit of crap in there...probably a load of Japanese seeds :( better get the Croc Hunter and quarantine onto it...crikey!

  • 1 year later...
  • 2 months later...
  • 5 months later...
  • 1 month later...
  • 3 months later...
  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...