Jump to content
SAU Community

Q45 Throttle Body Install.

Daboss

By Daboss,
in Engines & Forced Induction

 Share

Recommended Posts

Daboss Experienced

Daboss

Posted
Posted

Hey forum!!! As topic states I need a little help wiring the q45 throttle body to a series 2 rb25det. I already have the grey plug wired to the rb25 tps plug, but I am stumped as what to do with the wires that go to the black box on the side of the throttle body. A tutorial said to integrate into wiring but doesn't state how to. Can someone please explain to me what to do with the three wires that come out of that black sensor? Thanks.

Link to comment
https://www.sau.com.au/forums/topic/308397-q45-throttle-body-install/
Share on other sites
Dale FZ1 Veteran

Dale FZ1

Posted
Posted

There are two plugs on the TPS, one on the flying lead, and the other onthe TPS body.

There are two corresponding plugs on your loom. Simply plug them in. As per the tutorial you will possibly have to cut the loom to make things the right length and tidy things up a bit.

Daboss Experienced

Daboss

Posted
  • Author
Posted
There are two plugs on the TPS, one on the flying lead, and the other onthe TPS body.

There are two corresponding plugs on your loom. Simply plug them in. As per the tutorial you will possibly have to cut the loom to make things the right length and tidy things up a bit.

Wow you totally lost me. Let me tell you what I did. So far I have spliced the grey plug off the q45 to the brown plug off the series 2 rb25. Now I need to know what to do with the plug that comes off the black sensor of the q45.

Daboss Experienced

Daboss

Posted
  • Author
Posted
There are a couple of threads around

This one might help

http://www.skylinesaustralia.com/forums/Q4...html&hl=q45

Ok do you see the picture in the link you sent. That grey wire I have wired up already, that part is fine. It is just that little black box that is on the side of the throttle body, I want to know what to do with the wires that come from there. That part I do not get is, the tutorial says to integrate the stock wires into the vq45 plug(with a pic of that black box above it). How do I do that? Can someone just say were to connect the wires of the plug that will be coming from the little black box. The grey plug is all wired up and everything is good with that.

http://www.skylinesaustralia.com/forums/Q45-T-b-t118484.html

That is the link to the tutorial I followed, just need to know what to do with the wires that come from the black sensor.

woolls Experienced

woolls

Posted
Posted

I asked the question on nico club .com, and I got a response, "you don;t need to worry about that plug. it goes to one of the big white plugs near the ecu that aren't used"

I have had mine Running with only 1 plug connected, it seem to run fine, but After 4 laps on the track, the turbo exhaust housing got way to hot and is now stuffed (warped).

Don't know if it has anything to do with how the TPS is hooked up, but that was the only thing I have changed and the car was fine before. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • MBS206
      NC MX5

      By MBS206 · Posted

      Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...