Jump to content
SAU Community

Damo's R32 Gts-r, On Going Project Fun Car. History And Use Full Info


Recommended Posts

well it probably looks worse than it is. it is dead square with the rad suport pannel.

that spot is where the GTR trust and HKS oil cooler kits are mounted also as there is no room in the right hand side.

and im putting a duct directly onto it so that should help also.

thanks for the query thoe. other peoples perspectives are always handy.

Are you running a thermostat or different PS oil with the cooler Damo?

Edited by XRATED
  • 3 weeks later...
nope just as normal.

I just bypassed my hicas solinoids and run the rear pump through the stock power steering/hicas oil cooler loop in the front....

The hicas soliniods are heavy!

Any updates damo? Still heading to the symonds gymkhana?

Cheers

Justin

  • 3 weeks later...

thought i best do a quick update. this time of year is hell for me so very little time sent on my car.

parts ariving

10112010092.jpg

box opened

10112010094.jpg

motivation growing

10112010098.jpg

test fitting for the fun of it.

10112010099.jpg

ive gathered the 3 1/2 inch stainless bends needed to make the dump and have been getting everything ready to go back together.

New deadline is a week before powercruise. chuck in xmas and new years and ive got about 3 weeks fee to complete it.

  • 2 weeks later...

update

adapter plate and first part of the plenum bolted up ready to go on. all going well this time tomorow the head will be in place and everything will start to happen

12122010124.jpg

ive been tidying things up and painting bits and bobs ready to be put back on the car like this cusco master cylender stopper that used to be blue.

08122010120.jpg

ive finaly given the car pride of place in the shed ready to be attacked from every angle. and destickered it on one side.

12122010125.jpg

i decided i wont have time to build a full exhaust the way i wanted so i brought a twin 2 3/4" system that i will still have to modify but should save me some time. ill also be keeping the rear mufflers as id like the sound level to be resinable. especialy for my nebours sake with late night loading sessions.

12122010127.jpg

ive also gathered most of the speed flow fitting to plumb up the turbo. and am getting a fitting welded to the fuel rail for my fuel pressure sender to tidy up some more lines.

Ok so i got the head on during the week. no exciting pics there.

i braced up the exhaust manifold thismorning as out of all my friends cheap manifolds the only one not to have cracked yet is the only one that had any sort of bracing between the main flange and the turbo flange. then i bolted the manifold up to the engine. because the manifold was origanly for a t4 turbo it had an adapter plat to t3 but was missing the bolts so i got some cap bolts during the week and machined them down to fit at work. the last bit i got done today was the test fitting the turbo to see how the dump pipe will fit.

19122010134.jpg

during the weekend i went and brought some bits off an ex-skyline owner. its funny how people acumulate heaps of shit out of skylines. the bloke had boxes of stuff he no longer needed. it was very temptiong to take it all but in the end i walked away with an old nardi wheel. a stock airbox as they are getting harder to come by and a spare boot lid so i can run multiple wing options. when i got the wing home i noticed that it has some very JDM rare stickers on it.

19122010131.jpg

19122010132.jpg

19122010133.jpg

i was stocked as i had only recently been reading up about the R32 GTR touring cars.

  • 3 weeks later...

No updates for me but i am after some readers help

does anyone have any good pictures of r32s with side pipes. im after r32s mainly but r33 34s would eb good also. im trying to come up with a good designe for a side pipe for low cars.

No updates for me but i am after some readers help

does anyone have any good pictures of r32s with side pipes. im after r32s mainly but r33 34s would eb good also. im trying to come up with a good designe for a side pipe for low cars.

Out the passenger door!

Have a look at russ's build thread for they're black r34gtr (hi-octane 34) for an awsome side pipe!

i've already sudjested the tunnel in the floor, and the door pipe. i doubt cams would let you run a door pipe, and i think his passengrs would sook

seeing as he doesnt have any ABS why not just go 90 degrees off the back of the turbo out the side of the front guard?

the only other way to get one on a low car that comes to mind would be to get some 4" or 5" pipe and have it crushed to its an oval shape for extra ground clearance where it passes under the chasis rail. (assuming you dont want to cut and reinforce it)

i've already sudjested the tunnel in the floor, and the door pipe. i doubt cams would let you run a door pipe, and i think his passengrs would sook

Well fk it all and turn the dump pipe upside down... run it right out the bonnet! H a ha ha.

also sudjested that one too :P

How about bolting a truck stack to the passenger guard?

Hot rod (cobra style) shrouded side pipes instead of side skirts?

Under the car, into the cabin behind the passenger seat, out through the rear guard behind the passenger door... Just build a box/heat shield over it in the cabin.

J.

all good ideas. just trying to find the right one. most of the problem is complying within the cams rules.

i realy need some pics as i think i know how to do it i just need an idea of how it should look on the outside.

i also didnt realise that mark and russes car had many detailed pics. i will go for a hunt.

just copy the super taxis. put a few, smaller diameter pipes in under the chassis rail. I'm going to run twin 60mm, same as my dump pipes. I have run 3" sidepipe before but it did scrape at times

i had thought that to but wondered weather 3 or 4 or 6 pipes would look gay/ try hard.

the biggest concern if i run side pipes is the potential for damage to the turbo and turbo manifold as a result of hitting them at any speed and at odd angles. ive flown backwards off the track more times than i care to count at over 120km/h trying to enter sideways at my local track.

i had thought that to but wondered weather 3 or 4 or 6 pipes would look gay/ try hard.

which is why i suggested a semi crushed 4-5" pipe. if you are really worried, make up a bash plate for it.

yeah it's not easy to make a sidepipe for a 32 with any kind of sane ground clearance. mark and russ's 32 had the conventional just out the side pipe on the passenger side but it was pretty low. for marks car he cut the passenger floor and made a nice tunnel for it so it comes out level with the sills out through the side skirts. short of doing that to tuck it up in the body it's not easy.

the auto gallery R32 in japan runs one out the door. I have seen it up close and it's quite cleverly done. some pics:

autogallery%20rs6.jpg?__SQUARESPACE_CACHEVERSION=1289646946849

autogallery%20gtr%202.jpg?__SQUARESPACE_CACHEVERSION=1289639495793

DSC_7617-a.jpg

thanks Barron. i i had to pick my fav 32 it would be this one. im loving the small bits that get changed from time to time.

that seems to be the easyest way to do it. thanks rob.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...