Jump to content
SAU Community

Recommended Posts

Think there's a subtle difference in the skirts themselves as well, think it was something like more of a curve or indent in the actual skirt towards the middle, probably to accommodate for the difference at each end due to the guards...

I think I've seen people do it, but there was probably some work involved

F<------------------------------------------------------------------>R

166cm

<--------->

26.5

approx

mmsed you 3 photos alex let me know if you get them, looking closely at it the guards do go out pretty wide which is why its in 2 pieces from the looks of things

Anyone who's after a sick electronic boost controller (Turbosmart e-boost street) should consider buying mine.

Only $350.

http://www.skylinesaustralia.com/forums/topic/352443-turbosmart-e-boost-street-ebc/

Selling due to sale of car : (

yeh you'd think it would be easy to find em in white but i cant, so yeh was just an idea IF they fitted from the pics leigh sent it seems do able but not worth the effort its only side skirts anyway.

if you'ze see some in any colour stock hit me up do want. asap.

I don't wanna pay $300+ for that seat because I know they were $200 each not long ago haha.

Thinking about maybe a Velo or OMP fixed back... Around the $500-600 mark. Thoughts?

velo GP90 in black

that's what i'm going when i CBF spending the $$$, and the bride seat in the link is exactly what I am running at the moment, it's decent and would be easy to resell if you want a mint seat later... rails will set you back like ~$100 secondhand from j-imports and he usually has them in stock. fwiw it sits a good inch lower than GTR seat on superlow rails

looks like a fish tank

buy it and you can do whatever you want with it

sitting low is where it's at...when i took my seats out and put stockies back in to sell, felt like SHIT. felt like sitting ON the car rather than in it, and it was surprisingly un nerving taking a corner at any kind of speed in the stock seat as opposed to in the low, supportive aftermarkets I had

sweet, black?

hamish & dez- oic

i was sliding all over the stock 32 seats when i was fanging it through corners.. lower driving position= reduced center of gravity = driver being stable at speed?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...