Jump to content
SAU Community

Recommended Posts

hey all,

just picked up my car from getting tuned and stuff.

now what happens is when i accelerate and then either clutch in or let it rev down i get 1 or 2 massive back fires.. almost like if i was to do a keybanger!

it happens in every gear, and around the 1500-3000rpm..

the car has no boost leaks before the exhaust as we pressured the intake to hear for leaks but there all secure..

would having an exhaust leak cause this? as in the exhaust is sucking in air and mixing with the unburnt fuel and creating an (explosion)?

also,

my hiflow 7400cc stock injectors dont seem to be firing even at idle? is this due to them being too hiflowed?

mods:

rb25det unopened

stock exhaust manifold

z32 afm

nisstune rb20 ecu

eboost

fmic

3inch turbo back no mid mufflers or cat.

740cc hiflow stock injectors

gt3076r .82

turbosmart ultragate 38mm external wastegate

cheers Adrian!

Link to comment
https://www.sau.com.au/forums/topic/312593-car-making-loud-backfires/
Share on other sites

What do you mean by the injectors arent firing at idle? The fuel has to be coming from somewhere? I would say the ttp min setting needs to be adjusted as the larger injectors need less ms on overrun. You are running a recirculating BOV aren't you?

im running all standard lines to bov etc..

um it was tuned in adelaide buy the speedlab..

he worked on getting them to work better on idle..

its really anything under 1500rpm..

once u put some pedal into it, the car runs mint..

he thinks the 740cc injectors are too hiflowed for the stock ones.. so there not firing even under idle. like the car bounces from slightly lean to slightly rich..

he also thinks there may be an exhaust leak which is sucking air in under de-acceleration which is mixing with the unburnt fuel and making the (explosion).

he thinks the 740cc injectors are too hiflowed for the stock ones.. so there not firing even under idle. like the car bounces from slightly lean to slightly rich..

he also thinks there may be an exhaust leak which is sucking air in under de-acceleration which is mixing with the unburnt fuel and making the (explosion).

If that's the case, your whole tune should be richer then what the actual AFR was reading...

But more it sounds like the injectors should be replaced... 700cc should idle perfectly. And if you check all the exhaust and find no leaks I'd be looking at the tune and injectors.

nah bluey white smoke..

just about to pull plugs out. wait for the tool..

i would have thought missfire = black smoke due to unburnt fuel?

but this is white.. turbo is new, oil is new, plugs were new, injectors new... hmmm

oh ans splitfire coilpacs

Edited by rad32
he thinks the 740cc injectors are too hiflowed for the stock ones.. so there not firing even under idle. like the car bounces from slightly lean to slightly rich..

he also thinks there may be an exhaust leak which is sucking air in under de-acceleration which is mixing with the unburnt fuel and making the (explosion).

Do you KNOW they're not firing at idle or just SUSPECT it? If the car is extra rich at idle/low load but ok otherwise, then the injector latency setting may be too big. However if the latency is too low you'll get extra lean at idle/low load when its ok at load...

If the system is working in closed loop control (ie the o2 sensor is being used) then its supposed to bounce from lean to rich and back again constantly - thats how it works.

BTW black smoke = rich, white/blue smoke is oil burning.... nasty.

well i just pulled the plugs out and 1,4,5 were very wet.

then we cleaned them put them back, started it and same,

then we unpluged the coilpacks and 2,3,6 made change and ,1,4,5 mad no change.

does that mean 1,4,5 are getting too much fuel?

as they would be making the car miss?

i dont know why white smoke would be coming out?

yesterday the car was running fine (black smoke) so richish.

Bluey/white smoke means oil and possibly water is getting in to the combustion chamber / exhaust - never good unfortunately...

Off the top of my head could be piston rings, a cracked head or blown turbo seals... could also be valve stem seals but doesn't sound like it

A few things you can check:

- Take the pipes off the turbo compressor and check for excessive oil - stuffed turbo, could also be coming from the exhaust side - a bit tricker to get the dump pipe off but a potential source. This can also cause problems with fuelling as air can move between the intake and exhaust

- Get a compression test done on the engine

- Check the water in the radiator, if it looks milky/oily you are most likely looking at a cracked head

Bluey/white smoke means oil and possibly water is getting in to the combustion chamber / exhaust - never good unfortunately...

Off the top of my head could be piston rings, a cracked head or blown turbo seals...

A few things you can check:

- Take the pipes off the turbo compressor and check for excessive oil - stuffed turbo, could also be coming from the exhaust side - a bit tricker to get the dump pipe off but a potential source. This can also cause problems with fuelling as air can move between the intake and exhaust

- Get a compression test done on the engine

- Check the water in the radiator, if it looks milky/oily you are most likely looking at a cracked head

oils fine, water is green, turbo is brand new and is all good..

what would be the reasong behind cyl 1,4,5 not making a difference when i unplug the coilpacks?

coz this would be the issue with the car running on less cyl yeh?

also does the gt30 need a more restrictive oil feed?

i dont believe i have any of the issues above as it only did 20 dyno runs and has been fine before that. and was also fine when i drove it off the car trailer..

its like something happened overnight..

When you say the plugs were wet - were they fouled with fuel, or were they wet with water?

Run through the basics air, fuel, spark, compression.

Air = your problems dont sound like a problem with air but check all intake piping is connected properly, there are no forgotten rags blocking intercoolers etc

Fuel = while the car is running you should be able to feel the injector pulsing, you could also check fuel pressure if you have the gear - would recommend a mechanic for this

Spark = you really need a spark tester for this these days - there are old methods but can potentially cause damage to the ignition module - mechanic would have one

Compression = compression test - again you need the gear

Once you have narrowed it down to one of the basics above, or none of the above, you can proceed to the next steps of diagnosis.

Not sure about restrictors for GT30 - I know first hand the GT2860 series have built in restrictors in the oil inlet - if you have a photo upload it, but worth checking with the experts - give GCG or similar a call.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...