Jump to content
SAU Community

Recommended Posts

hey all,

just picked up my car from getting tuned and stuff.

now what happens is when i accelerate and then either clutch in or let it rev down i get 1 or 2 massive back fires.. almost like if i was to do a keybanger!

it happens in every gear, and around the 1500-3000rpm..

the car has no boost leaks before the exhaust as we pressured the intake to hear for leaks but there all secure..

would having an exhaust leak cause this? as in the exhaust is sucking in air and mixing with the unburnt fuel and creating an (explosion)?

also,

my hiflow 7400cc stock injectors dont seem to be firing even at idle? is this due to them being too hiflowed?

mods:

rb25det unopened

stock exhaust manifold

z32 afm

nisstune rb20 ecu

eboost

fmic

3inch turbo back no mid mufflers or cat.

740cc hiflow stock injectors

gt3076r .82

turbosmart ultragate 38mm external wastegate

cheers Adrian!

Link to comment
https://www.sau.com.au/forums/topic/312593-car-making-loud-backfires/
Share on other sites

What do you mean by the injectors arent firing at idle? The fuel has to be coming from somewhere? I would say the ttp min setting needs to be adjusted as the larger injectors need less ms on overrun. You are running a recirculating BOV aren't you?

im running all standard lines to bov etc..

um it was tuned in adelaide buy the speedlab..

he worked on getting them to work better on idle..

its really anything under 1500rpm..

once u put some pedal into it, the car runs mint..

he thinks the 740cc injectors are too hiflowed for the stock ones.. so there not firing even under idle. like the car bounces from slightly lean to slightly rich..

he also thinks there may be an exhaust leak which is sucking air in under de-acceleration which is mixing with the unburnt fuel and making the (explosion).

he thinks the 740cc injectors are too hiflowed for the stock ones.. so there not firing even under idle. like the car bounces from slightly lean to slightly rich..

he also thinks there may be an exhaust leak which is sucking air in under de-acceleration which is mixing with the unburnt fuel and making the (explosion).

If that's the case, your whole tune should be richer then what the actual AFR was reading...

But more it sounds like the injectors should be replaced... 700cc should idle perfectly. And if you check all the exhaust and find no leaks I'd be looking at the tune and injectors.

nah bluey white smoke..

just about to pull plugs out. wait for the tool..

i would have thought missfire = black smoke due to unburnt fuel?

but this is white.. turbo is new, oil is new, plugs were new, injectors new... hmmm

oh ans splitfire coilpacs

Edited by rad32
he thinks the 740cc injectors are too hiflowed for the stock ones.. so there not firing even under idle. like the car bounces from slightly lean to slightly rich..

he also thinks there may be an exhaust leak which is sucking air in under de-acceleration which is mixing with the unburnt fuel and making the (explosion).

Do you KNOW they're not firing at idle or just SUSPECT it? If the car is extra rich at idle/low load but ok otherwise, then the injector latency setting may be too big. However if the latency is too low you'll get extra lean at idle/low load when its ok at load...

If the system is working in closed loop control (ie the o2 sensor is being used) then its supposed to bounce from lean to rich and back again constantly - thats how it works.

BTW black smoke = rich, white/blue smoke is oil burning.... nasty.

well i just pulled the plugs out and 1,4,5 were very wet.

then we cleaned them put them back, started it and same,

then we unpluged the coilpacks and 2,3,6 made change and ,1,4,5 mad no change.

does that mean 1,4,5 are getting too much fuel?

as they would be making the car miss?

i dont know why white smoke would be coming out?

yesterday the car was running fine (black smoke) so richish.

Bluey/white smoke means oil and possibly water is getting in to the combustion chamber / exhaust - never good unfortunately...

Off the top of my head could be piston rings, a cracked head or blown turbo seals... could also be valve stem seals but doesn't sound like it

A few things you can check:

- Take the pipes off the turbo compressor and check for excessive oil - stuffed turbo, could also be coming from the exhaust side - a bit tricker to get the dump pipe off but a potential source. This can also cause problems with fuelling as air can move between the intake and exhaust

- Get a compression test done on the engine

- Check the water in the radiator, if it looks milky/oily you are most likely looking at a cracked head

Bluey/white smoke means oil and possibly water is getting in to the combustion chamber / exhaust - never good unfortunately...

Off the top of my head could be piston rings, a cracked head or blown turbo seals...

A few things you can check:

- Take the pipes off the turbo compressor and check for excessive oil - stuffed turbo, could also be coming from the exhaust side - a bit tricker to get the dump pipe off but a potential source. This can also cause problems with fuelling as air can move between the intake and exhaust

- Get a compression test done on the engine

- Check the water in the radiator, if it looks milky/oily you are most likely looking at a cracked head

oils fine, water is green, turbo is brand new and is all good..

what would be the reasong behind cyl 1,4,5 not making a difference when i unplug the coilpacks?

coz this would be the issue with the car running on less cyl yeh?

also does the gt30 need a more restrictive oil feed?

i dont believe i have any of the issues above as it only did 20 dyno runs and has been fine before that. and was also fine when i drove it off the car trailer..

its like something happened overnight..

When you say the plugs were wet - were they fouled with fuel, or were they wet with water?

Run through the basics air, fuel, spark, compression.

Air = your problems dont sound like a problem with air but check all intake piping is connected properly, there are no forgotten rags blocking intercoolers etc

Fuel = while the car is running you should be able to feel the injector pulsing, you could also check fuel pressure if you have the gear - would recommend a mechanic for this

Spark = you really need a spark tester for this these days - there are old methods but can potentially cause damage to the ignition module - mechanic would have one

Compression = compression test - again you need the gear

Once you have narrowed it down to one of the basics above, or none of the above, you can proceed to the next steps of diagnosis.

Not sure about restrictors for GT30 - I know first hand the GT2860 series have built in restrictors in the oil inlet - if you have a photo upload it, but worth checking with the experts - give GCG or similar a call.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...