Jump to content
SAU Community

Recommended Posts

I got my best times on the KU36 starting at 36psi cold. Didn't make note of the hot pressures. But the heavyweight Supra probably put a couple of extra pound in them through heat than your lighter R32.

Cheers guys, that will save me a bit time playing around with pressures! I'm going down in 2 weeks and i'll let u know how i go:)

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

hey guys, great topic. Any cahance of listing the tyres in some sort of performance category or compound list and with the average prices.

i havent had a new set of tyres on my car yet, still using the secont hand RE55s off the v8 utes. I want to no im spending the right money when the time comes, and you guys seem to have the majority covered. I dont think i can run the bridgestones again at $440 a corner.

My opinion of relative performance and price of semi slicks:

Dunlop DZ03 (expensive)

Bridgestone Re55s (expensive, now)

Yoko A050 (expensive)

Kumho V70A (medium)

Toyo 888 (medium)

Pirelli P-Zero (v expensive)

Yoko A048R (expensive)

Just a guess on the yoko a050 I have not run them personally. they might be quicker than the re55 but its hard to tell because they are a softer compound. Also bridgestone are terrible in the wet with low tread, and the kumhos provide consistent grip well below the wear markers (ie they last a long time without dropping off). Yoko A048 are OK for first 3 laps but drop of really quickly, well before they wear out.

I don't know anything about the 2nd tier tyres (falken azenis, kumho ku36, federal 595rs etc etc) except that you will loose at least a second or 2.

ultimately if you want to win you need to buy new dz03s each time. anything else depends on how much you can compromise.

and for social track days etc.

My opinion of relative performance and price of semi slicks:

Dunlop DZ03 (expensive)

Bridgestone Re55s (expensive, now)

Yoko A050 (expensive)

Kumho V70A (medium)

Toyo 888 (medium)

Pirelli P-Zero (v expensive)

Yoko A048R (expensive)

Just a guess on the yoko a050 I have not run them personally. they might be quicker than the re55 but its hard to tell because they are a softer compound. Also bridgestone are terrible in the wet with low tread, and the kumhos provide consistent grip well below the wear markers (ie they last a long time without dropping off). Yoko A048 are OK for first 3 laps but drop of really quickly, well before they wear out.

I don't know anything about the 2nd tier tyres (falken azenis, kumho ku36, federal 595rs etc etc) except that you will loose at least a second or 2.

ultimately if you want to win you need to buy new dz03s each time. anything else depends on how much you can compromise.

I dont want to hijack the thread but i dont think its worth starting another one for a very similiar topic.

What is the largest set of semi slicks and full slicks that can be fitted on a 32 gtr? I am looking at 295s all round, is this possible or go abit smaller like 275s? Im running 17 inch rims, havent purchased them yet but looking at 10' wide rims too, so will 295s be too wide for those? whats the ideal size for a gtr for time attack sort of stuff. Its a pretty serious engine combo etc so i want as little traction issues as possible.

Whats the best options for full slicks for this sort of stuff, and rough idea on prices?

If the mods feel this isnt on topic then delete it and ill start a seperate thread.

stu I'd run the toyos or kumhos depending which is cheaper for bashing around the track. but sooner or later you will want to know "what is the best time this car can do", and the only way to find out is to put the best tyres on it. About 350 each instead of 500. Careful with second hand ones, they look cheap but can we well and truely rooted even if they still show tread depth (heat cycles kill them not wear)

lets say the dunlop and bridgestone are a second quicker than the next best tyres (possible at some tracks).....imagine how frustrating it is to try and make up that second through power, suspensions settings, different driving lines etc when you could just bolt the right tyres on.

Combined Touring Cars went from A048 control tyres to Kumho V70A and went a full second faster. Then control tyres were dropped, the front runners are buying new dunlops and bridgies, and going 1.5 to 2 seconds faster again. Improved Production still run A048 and despite far more mods being allowed (eg engines are free esp for non turbo cars) their quickest cars are slower than the fastest production cars.

  • 2 weeks later...

Boy, $275 a tyre!! :cool:

Makes me glad to be driving a little buzzox shopping trolley on 15's!! The RSR 595's are $120 a corner, so at that price I might grab a set once the 048's wear out. These are meant to be 140 treadwear - correct? (not sure if I'm reading the specs correctly). These track tyres are all new to me.

Point taken about wanting to know what the car;s capable of. Before I get there, I need to first learn to drive the car properly, then get to know the track (Lakeside) then start thinking about tyres and suspension (it's currently set up for gravel, with about 4" excess ride height). Depending on how well I take to tarmac work (loved lakeside) I'll look at what my options are.

lol.....mine are 500-550 a tyre....

Hi All

Just had a quick glance, on R32 at 300kw,Yoky A050's Softs with, front 34psi Rear 32 Hot at most events up to 5 laps or not too hot a day - on the R33, (370kws) at Oran Park with brand new DZo3's 285x30x18 SR's were a clear second slower than Yoky A050's 265x35x18 this is also case at the same test at Eastern Creek. So keeping this in mind Yoky's wear a bit quicker, produced the best time and over $1000 a set cheaper. although in longer race conditions say 10 - 20 laps, the DZo3s are nicer to drive on.

yeah they have had some great results, on your cars and others in sprints, hillclimb etc.

can't work for me because we have min 3x 20min races and they will just get smashed....even gordon leven were not willing to recommend their hardest a050s for race use.

also not a great deal for most people doing longer track sessions.....but obviously a great choice if you are only doing 3 laps at a time

i have used Khumo semi's and Bridgestone re55.

Bridgies came up to temp earlier and held consistantly lap after lap.

Used khumo's took a while to build up temp and then held really good... they seemed to be good value for money. Not real good for hillclimbs though! :)

i have used Khumo semi's and Bridgestone re55.

Bridgies came up to temp earlier and held consistantly lap after lap.

Used khumo's took a while to build up temp and then held really good... they seemed to be good value for money. Not real good for hillclimbs though! :ermm:

that all depends what compound Kumhos you bought.

Kumho V70's are pretty good value for money and I think they are a very underated tyre, most people write them off as a basic motorsport tyre.

I think this is because when you look at the V70 Semi's, they don't look like your regular RE55 or A048's. The tread depth is very shallow and they don't have huge tread blocks.

However, when I gave them a go; the grip was very good, and they held up to the heat very well. I'm only doing 5 laps at a time but I have excellent grip the whole time.

I can only compare them to Advan A048's I've run previously and they were at least 2 second's a lap quicker.

I would expect more expensive tyres such as DZ03's, A050's and RE55's to be slightly better, but for the price I paid ($330e each for 245/40/17) I'm fairly impressed with them.

Hmmm... Once my Kumho's wear out, I'd really like to try the soft A050's after hearing so many good things about them.

^^^^ That is contrary to our experience with them. we ran them for two Targa Tasmanias, once on a '02 STi and the other time on a 34 GTR, and they were a great tyre, unmatchable in the wet in my opinion.

Their outright dry performance has been surpased now though.

We also found they worked best at lower pressures, liking to start around 24 cold and setting them at 30 hot.

^^ I was about to say the same thing. I don't think I run high pressures in the Kumho's to make them work. I've never had them over 35 psi hot and try to keep them around 32 psi hot.

Also, I had to get a price on the Advan A050's and in 245/40/17 size they are $485 each from Gordon Levin.

Edited by nismoman

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...