Jump to content
SAU Community

Recommended Posts

Opinions on a 6466 w/ .84 TS on a built 2.6 with 272/272 10.2mm lift cams?

I have poured through this thread, and as such was leaning towards the 6262 or even considered the 6062 Gen2 thats just been released - but my engine builder is telling me the 6466 is 100% the go

I trust the workshop, but just want to double check other's results; dont want something that comes on at 5k or later.. id rather it come on hard at 4.2-4.5k rpm

Its concerning seeing people say a 6466 outflows a T51R

A rb30 usually adds about 500rpm response all things equal... My cams are bigger than yours, so you could possibly base it off that. I'm using a 1.0 divided housing.

I don't think it will be bad, certainly better than a T51R in response, even if it does flow more top end. Thats the beauty of new technology.

If you're worried about response though your are probably better off with a smaller turbo, unless you have a power figure you definitely want. Take into account the 6466 is a 600awkw turbo

Depends on car use, I'd be giving a 6062 a go if your stuck between the 6262 and 6466 for a decision. It should sit right in the middle in response and power :)

I try and do everything with my car from tight sprints, circuit work,1000m drags and powercruise etc. and the 6262 is right in the sweet spot of power and response. I actually turn it down 140hp for everything apart from powercruise and drags because it's more than enough. What do you want from your car?

A 6466 is going to be responsive for its size but it's getting towards drag car only power band on a 2.6L, if that's what you want then go for it but your never going to keep up with the Jones's.

What would you guys recommend for. Street drag VL, auto re401a

Forged Rb30 NEO head

270 9.2mm cams

Plenum etc etc 3k stall

Currently running gt35 .82 internal gate

22psi 422hp but out of injectors

98ron

I was looking at the 6466

6466 1.0 divided.

I make 433awkw on 22psi, 98

100kw more on e85

Should be plenty to run 9's

It's been a while but here is my Dyno sheet from build

Rb26 precision 6262 at 19 psi.

Car is running good other than its smoking from turbo.

Anybody here using restrictors? I just put a .030 restrictor and stopped smoking but not sure if I should drive it.(n1 pump)

EC990DBB-75E3-4453-89C1-EC9B0C5E4339_zps

Thanks for the quick reply guys. Haven't removed the factory restrictor. I'm running a -4an feed line and a -10 am drain line. Drain line is pretty straight down with now kinks. I also did a leak down test and compression test on the engine. Got 128 psi on all 6 cyl.(running 8:3:1 CR) and dry leak down test was 10% on al 6 but #1 13%. Not sure what other options I have

I'm getting 45psi. Pressure at 2.5-3krpms and over 60 psi from 4k up

Edited by silvianc

Is that America?

because that is epic power in Australia for that boost

Lol yeah. I'm in the U.S.

Setup made

390hp@9psi

450@11psi

560@15psi

611@19psi

This is on a 2.6, 87mm pistons and Tomei type B cams, t4 .84 divided housing and limiter on 8400 Rpms but u can see dyno sheet actually was 7.8k Rpms

https://m.facebook.com/story.php?story_fbid=773329676088103&id=142284982525912&_rdr

Our horses are angrier

It's been a while but here is my Dyno sheet from build

Rb26 precision 6262 at 19 psi.

Car is running good other than its smoking from turbo.

Anybody here using restrictors? I just put a .030 restrictor and stopped smoking but not sure if I should drive it.(n1 pump)

EC990DBB-75E3-4453-89C1-EC9B0C5E4339_zps

Hell yeah. I'm in the USA too. Here I am thinking of seeing 550 whp on pumpgas and I'm at sea level and I'm on a stroker motor. Heck I may see 650 whp on pump after seeing this !

Hell yeah. I'm in the USA too. Here I am thinking of seeing 550 whp on pumpgas and I'm at sea level and I'm on a stroker motor. Heck I may see 650 whp on pump after seeing this !

You'll probably see 550 Australian horses if you've been looking at our graphs. More if in USA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...