Plazmaman Plenem Vs Greddy

[muchogarcia34]

wish i knew before about this F*kn manifold..

someone must have run top feeds with a plazmaman..

I run top feeds with a plazmaman. But I'm using a Neo head so I don't know if that makes a difference........

[dori34]

what have plazmaman said in regards to what injectors you can run?

[rad100]

they said we will have something out at christmas..

no help to me.

[dori34]

that sux..

im sure someone here is able to help you.

have you tried posting a new thread?

[rad100]

nah i havent, dont really like starting new threads.

i see so many ppl get flammed..

fingers crossed someone can help.

[dori34]

check this out, you posted in there too but the guy posted some pics also..

http://www.skylinesaustralia.com/forums/topic/363530-plasmaman-plenumfuel-rail-problem/

[darrinspencer]

I run top feeds with a plazmaman. But I'm using a Neo head so I don't know if that makes a difference........

RAD32 - Neo rb25det use a 3/4 length injector same as FG falcons.

I have a greddy style inlet, so it is made for R33 sidefeed injectors, but I have a Neo rb25 and still use top feed injectors and aftermarket HKS stlwe rail. I will measure the overall height so you can see if they will fit under your plazmaman.

[PM-R33]

Is it hitting on the plenum itself or on the AAC? Because if it is on the AAC you can get a spacer plate for it.

[rad100]

phil any idea where i can get this so called spacer?

[PM-R33]

Actually now that I think about it maybe it was custom made...hmm. Basically was just a thick bit of aluminium the same shape as the AAC hole on the Plamaman plenum to push the AAC out about an inch so it wouldn't foul on a top feed fuel rail.

[rad100]

well apparently the id1000 3/4 injector sit 1cm lower, so now im just on the hunt for the least bulky 14mm fuel rail.

any ideas on where to grab one?

[Tony de Wonderful]

Guys where can you get the phelotic spacer thingy?

[Moodles2]

Gizzmo make a phenolic intake gaskets

[FineLine]

Guys where can you get the phelotic spacer thingy?

Mace engineering in melbourne made mine.

[BMYHOE]

Just engine management may be able to help

[Tony de Wonderful]

Hi where does the Plazmaman plenum have an off take for the brake booster?

I see a place at the back for the Idle control valve, and one large port underneath for the cold start valve, but nothing for the brake booster?

[PJ.]

I've seen the completed prototype billet rail for the R33 plenum, Plazmaman will be releasing it next month finally! Will be able to run full length top feed injectors.

[PJ.]

Taken from their facebook page: http://www.facebook.com/pages/plazmamancom/229267523757328

[SilverECR33]

whoa. watchout a vs thread survives.

[Ryno]

After reading all these post I've come to the conclusion that I probably went down the wrong path when I chose the plenum for my setup.

What I went for is a copy of the Jun manifold with a 80mm throttle body, this setup would be ideal for a RB2530 due to the peak power it can flow and it would also negate the bonnet clearance issues. But for my setup (given my car is a daily drive) I could do with the extra torque low in the rev range that the Plazmaman would give. The shame is, I love the look of the current manifold...

So if someone is looking for a manifold like mine get in touch, as it may give me the nudge I need to bite the bullet and go for the Plazmaman.

Edited May 4, 2012 by Ryno