Jump to content
SAU Community

Recommended Posts

Hi all,

I got done by the EPA. I need to remove my Piggyback ECU (UNICHIP). Is it just a matter of pulling it out, and removing the relevant wired up connections?

I also have larger injectors, and Z32 AFM. I will be removing these and replacing with stock items.

Once these are removed i just reset my ECU and the car will run?

Or is there anything else i need to do for it to run off standard computer?

Link to comment
https://www.sau.com.au/forums/topic/315807-removing-piggyback-ecu/
Share on other sites

You will see that some piggy backs actually run in series with the ECU wiring, just remove the piggyback & join back the relevant wires.

As long as you replace the aftermarket larger injectors & Z32 your car will run fine off the standard computer. Also make sure your base timing is correct to, the previous owner/tuner may have adjusted the CAS to suit the piggy back.

I pulled the Kick Panel off my GTR today, when I bought the car I was told it had a MIMO Piggyback (Dunno What that is) but cant actually see anything that looks like an ECU of any kind only a little brown box with some heavy gauge wires coming out of it, Plenty of Splicing though!!

post-34973-1270690830_thumb.jpg

post-34973-1270690891_thumb.jpg

greensa14 - totally depends as others have said - how the UNICHIP is installed.

Perhaps get some pics?

If you have to unwire it and so on, it's going to be a pain in the ass.

You'd be better off with a PFC or something that is a replacement setup - 30 sec to remove from the factory harness.

Ok thanks for clearing that up I will have to look a little deeper, has Nismo AFM's so there has to be something in there surely!!

Open the cover. I'd say it's a chip on the actual ECU board.

There is no way you'll have aftermarket AFM's without a chip to alter it as there is no wire-in piggy back in those pics :woot:

I had a look last night. It is an external ecu that has been tapped in to the other wires on the factory unit to obviously change the readings as they pass through.

So it looks like i need to remove the spliced wires and re-solder the factory ones so they dont bypass.

Yea PFC would be good, but over worrying about defects etc. Dont want anything visible.

Looking at going Nistune.

why is a nistune (or unichip for that matter) illegal? they are not programmable on the fly, and the factory ECU is just as retunable as they are.

Surely the final emission is the only issue for legality? Plenty of shops in NSW that can provide a tune that will get you past the emissions test, why would Vic be different?

why is a nistune (or unichip for that matter) illegal? they are not programmable on the fly, and the factory ECU is just as retunable as they are.

Surely the final emission is the only issue for legality? Plenty of shops in NSW that can provide a tune that will get you past the emissions test, why would Vic be different?

Nistune can be retuned - the EPA here is retarded is the basic sense, archaic laws with no common sense.

Unichip go through the ADR testing/approvals, Nistune has not and can be retuned anytime.

Unichip you have to go back to them for (assumingly).

What is the criteria for an aftermarket system to meet ADR over there?

Nistune board can be PIN locked once the tune was able to meet emissions. The only way to retune it then is use the original PIN or reflash the board outside of the ECU

Transport SA documentation I have previously read states that any aftermarket/reprogrammed ECU will not be accepted due to the cost of the emissions testing required. However things may have changed since that was published

Cause we have some whack ideas down here.

A number of rules surrounding car modifications make zero sense.

The 1 intake mod for example. Senseless. No aftermarket ECUs....senseless.

I might get in touch with my local member and get her to ask Tim Pallas for a "please explain".

What is the criteria for an aftermarket system to meet ADR over there?

Nistune board can be PIN locked once the tune was able to meet emissions. The only way to retune it then is use the original PIN or reflash the board outside of the ECU

Transport SA documentation I have previously read states that any aftermarket/reprogrammed ECU will not be accepted due to the cost of the emissions testing required. However things may have changed since that was published

Vic is near enough to the same for the sake of the conversation.

PIN lock means nothing.

If its reprogrammable, not factory, its not allowed until all the full testing is done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...