Jump to content
SAU Community

Recommended Posts

So I'm selling my JZX90 and getting an M35 Stagea after seeing one locally and being stunned with it's good looks, AWD and practicality. The Iron Chef has sent me some auction lists but I don't know what is what. I want 2.5 turbo, awd cloth interior. What's an Axis and all the other nomenclature mean? I didn't realise how many different models there were! Can someone explain the difference to me please?

Link to comment
https://www.sau.com.au/forums/topic/316965-im-buying-an-m35-stagea/
Share on other sites

Wow, first time I've seen someone say they are good looking. Perhaps they are growing on all of us :D

I think they are hot! with a subtle kit, wheels and suspension they look aggressive yet practical ;)

I now look back at pics of my old C34 and its soo out-dated now... (not meaning to start an m35 v c34 war! haha)

I guess beauty is in the eye of the beholder! I like something different from everyone else and the M35 is waaayyyyy better looking than the C34 imo. Some big wheels brings the body size back into proportion. I saw one in the flesh with qld plates on it in my street 2 days ago and then saw it again the next day and I just love the shape. Was it anyone on here, in Launceston 2 days ago in a white M35???

So, is the fuel economy as bad as people have warned me? I've read the fuel economy thread and it doesn't seem toooo bad as in 14-16L/100Km in city driving and 10 or less on the highway. Is this genuine though and repeatable? I know once you have one it's hard to admit some shortcomings and i'm no different, whats the best and worst you guys have got from your M35 when its going properly and what are the best improvements to get better fuel economy out of it around town besides being easy with my right foot?

Edited by richzx

Best I have got, on a long country run is 600k's to light on.

Worst, this tank at the moment. Lots of short runs to work, running e85, cold mornings, lead foot, 300k's.

Generally on dino98 I was getting 450k to 65L.

Scotty forgets to mention that his car is the currenlty (lol) the most powerful M35 in the country.

For those with a relatively unmodified car the results are a bit better.

My car has a few mods which are mostly to do with suspension and brakes but on the engine side I have replaced the exhaust from the turbo back with a full 3" system and fitted a 16mm plenum spacer (really helps smooth out performance and improves economy on light throttle) and HDI intercooler.

City driving I get 13.5 - 14.3L / 100km (this is lots of hills and stop start traffic)

Highway Driving. I just did a 3500 km trip around VIC and with 4 people and a full boot and each tank was between 10.1 - 10.6L/100km.

This is for the ARX and the RX & RS are a little more economical as they are 17 inch wheels and slightly lighter.

these are real number that you can achieve. If you want to really push it all the time then expect higher numbers.

Cheers

Andy

Scotty forgets to mention that his car is the currenlty (lol) the most powerful M35 in the country.

LOL....no need to give him a big head.....I might do him soon on 98!!!!....e85's cheating :(

I'm running 18PSI and about 210AWKW's(under estimated) and I get about 425 to 450 per tank around 16lt's per 100km's around town.....could probably do a lot better around town if I wasn't continually hunting WRX's!!!!!.........open road and fully loaded I quite easily get 10 to 10.5lt's per 100km's....up over 650k's per tank without the aid of cruise control.

Edited by Jetwreck

Cheers guys. I think I'll be doing similar mods, an exhaust, plelnum spacer and the airbox CAI mod. These mods should all improve economy from what I've read. Just have to find the right car now and then the wait begins.

heh, mine is completely stock and used to average ~13.5-13.8L/100km in the summer (A/C on over 50% of the time).

If I went very lightly on the throttle everywhere I was able to get it down to just 13L/100km in the same conditions.

Now that the weather has cooled down here its averaging 12.5 L/100km which isn't too bad at all for a big heavy wagon, and with no conscious effort to drive economically.

Took it down to Robe over Easter and averaged 10.2L/100km. Thats with 2 adults, 1 baby, and a boot FULL (and I mean FULL) of gear, ranging from suitcases, pram, porta-cot, and enough food for 6 adults for the whole of easter! I think I filled every little compartment in the whole car...although everything was level with the top of the seats so I could still see out the rear (dont have a cargo barrier so had to make sure there were no loose items on top). I was impressed with how much went in. The 2 rear seats next to the baby seat were full of stuff as well (I try to put most of the weight as far forward as possible).

As for the M35 looks, I receive more (positive) comments from people about this car than I did when I owned the C34 (s2). I guess it just looks more modern.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...