Jump to content
SAU Community

Recommended Posts

I was at Eastern Creek yesterday and had an issue with the car that ruined the day. I have no idea what this is but here's what happened:

Car would only rev to about 3.5 to 4k at 11psi; it is tuned for 16psi in this range. From there the car would flutter and not want to rev any more. The problem is, this only occurs under full load acceleration; with light acceleration it's happy to rev to red line.

I checked all the hoses and nothing was loose and couldn't hear any leaks.

It's an R33gts-t and does anyone have an idea what this may be because I've got nothing??

Link to comment
https://www.sau.com.au/forums/topic/317390-car-not-holding-boost/
Share on other sites

I know you said you've checked all the hoses but that would still be my guess. On a track you are full load/full boost way longer than on the street, and things you might overlook can be loose.

so...check again....all clamps on the inlet....bov returns.....vacuum hoses....you need to look for splits as well as loose clamps too, tiny splits can open under boost but not be noticeable normally.

unless it sounds like a wrx of course!!

Thanks for your replies

Nah it didn't sound like a wrx. Car sounded normal and until it reached that flutter accelerated like normal.

I'll have to re-check all the hoses on it.

It's got after market coilpacks on it. I know it's an issue but how bad are these for going through coilpacks (as in after market ones)?

what spark plug gap are you running?

my car was boost surging from 16psi to 13psi on sunday on the way to eastern creek, i worked out the boost controller was playing up, after turning the boost controller off and running stock boost the boost was fine,

is your boost surging or the engine missfiring/ spitting?

what fuel pump your running?

OK I've had another look through the car the other day. I made a mistake above and the car does hold 16psi when it does this.

Checked the exhaust to see if it was a blocked cat but when the exhaust was off the car did the same thing but only when it was at half throttle.

Checked and cleaned spark plugs - all okay.

Unfortunately I didn't check the coil packs when the spark plugs were off. I will check these though. There's Splitfires on there but I don't know how long they've been on the car for.

Any ideas on what else that may be wrong with the car?

Hey.

When did you last change your fuel filter? It may be partially blocked.

Gap your plugs to 0.8mm.

Also What voltage are you running with your pump? If it hasn't been done already, you need to wire it directly to your battery with a 30amp relay in place for correct operating voltage.

If you are using the stock AFM you may also need to change it.

RB25DET AFM's are temperamental things especially when compared to Z32 or even R32 and don’t like to run too much boost through them especially on cold days/nights.

What ecu are you running?

If its stock the problem may also be a factory safe guard known as ‘rich and retard’.

If you running Splitfire’s they should be fine but if you’re concerned have them tested.

All in all it’s just a process of elimination but to me it sounds like air/fuel ratios are out which is known to occur around this rev range on RB25DET which tells me its running rich.

I hope this may help you in some way.

Cheers.

Hey.

When did you last change your fuel filter? It may be partially blocked.

Gap your plugs to 0.8mm.

Also What voltage are you running with your pump? If it hasn't been done already, you need to wire it directly to your battery with a 30amp relay in place for correct operating voltage.

If you are using the stock AFM you may also need to change it.

RB25DET AFM's are temperamental things especially when compared to Z32 or even R32 and don't like to run too much boost through them especially on cold days/nights.

What ecu are you running?

If its stock the problem may also be a factory safe guard known as 'rich and retard'.

If you running Splitfire's they should be fine but if you're concerned have them tested.

All in all it's just a process of elimination but to me it sounds like air/fuel ratios are out which is known to occur around this rev range on RB25DET which tells me its running rich.

I hope this may help you in some way.

Cheers.

Thanks heaps for that info. I hadn't checked the pump to see for blackages yet; regarding the voltage, I'm not sure what it runs but I'd presume it would be wired in for the appropriate voltage. Will double check though.

I probably should have put these up earlier but these are the engine mods the car has done to it:

Apexi Power FC

GCG turbo

Deatchwerks Injectors

Hybrid front mount intercooler

Z32 air flow meter

HKS boost controller

Apexi pod

Custom metal intake pipe

Splitfire coilpacks

Ganador 3” exhaust

Catco metal cat 5” body

JJR aluminium radiator

Nismo fuel pump

I don't know how long they have been on the car for. It's putting out about 260kW at the wheels

Edited by Gunnar_11

Sweet man, nice set-up.

Get a volt meter and check your pump for sure. It should be running at about 13-13.5 volts at idle if it’s been wired correctly. I forgot to mention that it might also pay to get a can of CRC MAF/AFM cleaner. This shit works wonders.

Other than that, I would change fuel filter and plugs (coppers, 0.8mm) for security and take it to a dyno to check air/fuel ratios.

I was at Eastern Creek yesterday and had an issue with the car that ruined the day. I have no idea what this is but here's what happened:

Car would only rev to about 3.5 to 4k at 11psi; it is tuned for 16psi in this range. From there the car would flutter and not want to rev any more. The problem is, this only occurs under full load acceleration; with light acceleration it's happy to rev to red line.

I checked all the hoses and nothing was loose and couldn't hear any leaks.

It's an R33gts-t and does anyone have an idea what this may be because I've got nothing??

still got the stock rubber in take? when they heat up they go soft an fold on them selfs stoping air flow

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok guys thank you very much. GCG highflow it is then 🙂 
    • forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...