Jump to content
SAU Community

Recommended Posts

I was at Eastern Creek yesterday and had an issue with the car that ruined the day. I have no idea what this is but here's what happened:

Car would only rev to about 3.5 to 4k at 11psi; it is tuned for 16psi in this range. From there the car would flutter and not want to rev any more. The problem is, this only occurs under full load acceleration; with light acceleration it's happy to rev to red line.

I checked all the hoses and nothing was loose and couldn't hear any leaks.

It's an R33gts-t and does anyone have an idea what this may be because I've got nothing??

Link to comment
https://www.sau.com.au/forums/topic/317390-car-not-holding-boost/
Share on other sites

I know you said you've checked all the hoses but that would still be my guess. On a track you are full load/full boost way longer than on the street, and things you might overlook can be loose.

so...check again....all clamps on the inlet....bov returns.....vacuum hoses....you need to look for splits as well as loose clamps too, tiny splits can open under boost but not be noticeable normally.

unless it sounds like a wrx of course!!

Thanks for your replies

Nah it didn't sound like a wrx. Car sounded normal and until it reached that flutter accelerated like normal.

I'll have to re-check all the hoses on it.

It's got after market coilpacks on it. I know it's an issue but how bad are these for going through coilpacks (as in after market ones)?

what spark plug gap are you running?

my car was boost surging from 16psi to 13psi on sunday on the way to eastern creek, i worked out the boost controller was playing up, after turning the boost controller off and running stock boost the boost was fine,

is your boost surging or the engine missfiring/ spitting?

what fuel pump your running?

OK I've had another look through the car the other day. I made a mistake above and the car does hold 16psi when it does this.

Checked the exhaust to see if it was a blocked cat but when the exhaust was off the car did the same thing but only when it was at half throttle.

Checked and cleaned spark plugs - all okay.

Unfortunately I didn't check the coil packs when the spark plugs were off. I will check these though. There's Splitfires on there but I don't know how long they've been on the car for.

Any ideas on what else that may be wrong with the car?

Hey.

When did you last change your fuel filter? It may be partially blocked.

Gap your plugs to 0.8mm.

Also What voltage are you running with your pump? If it hasn't been done already, you need to wire it directly to your battery with a 30amp relay in place for correct operating voltage.

If you are using the stock AFM you may also need to change it.

RB25DET AFM's are temperamental things especially when compared to Z32 or even R32 and don’t like to run too much boost through them especially on cold days/nights.

What ecu are you running?

If its stock the problem may also be a factory safe guard known as ‘rich and retard’.

If you running Splitfire’s they should be fine but if you’re concerned have them tested.

All in all it’s just a process of elimination but to me it sounds like air/fuel ratios are out which is known to occur around this rev range on RB25DET which tells me its running rich.

I hope this may help you in some way.

Cheers.

Hey.

When did you last change your fuel filter? It may be partially blocked.

Gap your plugs to 0.8mm.

Also What voltage are you running with your pump? If it hasn't been done already, you need to wire it directly to your battery with a 30amp relay in place for correct operating voltage.

If you are using the stock AFM you may also need to change it.

RB25DET AFM's are temperamental things especially when compared to Z32 or even R32 and don't like to run too much boost through them especially on cold days/nights.

What ecu are you running?

If its stock the problem may also be a factory safe guard known as 'rich and retard'.

If you running Splitfire's they should be fine but if you're concerned have them tested.

All in all it's just a process of elimination but to me it sounds like air/fuel ratios are out which is known to occur around this rev range on RB25DET which tells me its running rich.

I hope this may help you in some way.

Cheers.

Thanks heaps for that info. I hadn't checked the pump to see for blackages yet; regarding the voltage, I'm not sure what it runs but I'd presume it would be wired in for the appropriate voltage. Will double check though.

I probably should have put these up earlier but these are the engine mods the car has done to it:

Apexi Power FC

GCG turbo

Deatchwerks Injectors

Hybrid front mount intercooler

Z32 air flow meter

HKS boost controller

Apexi pod

Custom metal intake pipe

Splitfire coilpacks

Ganador 3” exhaust

Catco metal cat 5” body

JJR aluminium radiator

Nismo fuel pump

I don't know how long they have been on the car for. It's putting out about 260kW at the wheels

Edited by Gunnar_11

Sweet man, nice set-up.

Get a volt meter and check your pump for sure. It should be running at about 13-13.5 volts at idle if it’s been wired correctly. I forgot to mention that it might also pay to get a can of CRC MAF/AFM cleaner. This shit works wonders.

Other than that, I would change fuel filter and plugs (coppers, 0.8mm) for security and take it to a dyno to check air/fuel ratios.

I was at Eastern Creek yesterday and had an issue with the car that ruined the day. I have no idea what this is but here's what happened:

Car would only rev to about 3.5 to 4k at 11psi; it is tuned for 16psi in this range. From there the car would flutter and not want to rev any more. The problem is, this only occurs under full load acceleration; with light acceleration it's happy to rev to red line.

I checked all the hoses and nothing was loose and couldn't hear any leaks.

It's an R33gts-t and does anyone have an idea what this may be because I've got nothing??

still got the stock rubber in take? when they heat up they go soft an fold on them selfs stoping air flow

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...