Jump to content
SAU Community

Recommended Posts

Hi all

I was thinking of changing to a ford facing plenum to reduce the pluming and make the top of the engine look neater but then I wondered where I was going to put the bov. Is there a position that still makes it a plum back and how hard is this to do.

Thanks

Phil

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/
Share on other sites

at the risk or (re)starting an argument....I changed to FF plenum and didn't worry about the BOV.

Other than the silly noise when I change gears flat out, no issues so far. It is possible there is an impact on potential turbo life but there is a lot of opinions out there on that one. I was willing to take the chance as its a cheap turbo

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5191231
Share on other sites

Hi all

I was thinking of changing to a ford facing plenum to reduce the pluming and make the top of the engine look neater but then I wondered where I was going to put the bov. Is there a position that still makes it a plum back and how hard is this to do.

Thanks

Phil

Doing this at the moment. Generally put the bov between the the outlet of the fmic and the throttle body, so on the drivers side under the battery. Then you will need to run a pipe back to the inlet side, similar to a GTR setup.

I have a spare GTR BOV for sale while you are at it.

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5191255
Share on other sites

any updates on it darrin?

i still haven't started mine, still working on my ute :(

Pretty much ready to bolt up. I have been holding off because I was going to not use this plenum and buy a plazmaman instead, until I worked out the PM plenum will hit the bonnet with the rb30 in the future.

Might try and get some done tonight

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5192068
Share on other sites

could always run it on the hot side piping, makes it easy to run the plum-back pipe

I am planning to do this for mine as well. I have seen suggestions that it should be near the throttle body or near the turbo but when the bov opens pressure drop is the same everywhere so really it makes no difference where you put it so on the hot side is neatest.

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5192087
Share on other sites

Thanks for the info.

I think I will go with Darren’s idea and put it on the driver’s side under the battery and plum it back. I will have a closer look this weekend. I was hoping to reuse the bov to keep cost down.

Thanks again

Phil

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5192476
Share on other sites

I ended up putting mine on the hot side of the front mount as it made it much easier to pipe up. I must confess that I forgot I was running a panel filter and where I put the BOV it fouled the air box. Not to worry I went pod.Looks nice.

For someone who wants to go FF, if you can afford it, Darrin's idea is better. Get a Plazman. All you have to do is take the top off. All that stuff under the runners is a PITA.

Also if you are careful you don't have to move the washer bottle as Duncan had to do. And you can get two helicopter batteries on the tray giving 540 cca.

I'm fairly IT illiterate but if anyone wants some pics I will need an email address. So PM me.

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5192491
Share on other sites

i'm going to be using a std gtr setup but it has been welded to the bottom runners of a rb25 so it will bolt up. will be using std injectors as well, just have to get the neo fuel rail to bolt to the manifold and will run the rb26 aac valve becuase thats what the bottom air box has been made up to use.

ive been alittle busy with my hilux atm cos the engine died, and the stag is the MRS car which needs to be on the road all the time so playing with it is very minimal.

the only real other issue i have with it is the TPS. the neo and the gtr use different setups. wiring is similar in that they have 6 wires, 3 for tps and 3 for auto. i just need to know which colours are what on both to wire up.

here are some pics of my ute conversion too :D

IMG_0247.jpg

P1010051.jpg

post-4857-1271933300_thumb.jpg

post-4857-1271933311_thumb.jpg

post-4857-1271933319_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5194988
Share on other sites

Currently I run a chinese Greddy copy.

Worked ok, the front of it was cut off because of fitment and to weld the tb on but now theres a pinhole leak on one of the runner arms.

Bought a plazmaman and powdercoated intake runners so itll be on when Im more cashed up

As for fitment: went on ok (see above about the cut/weld, needed an SR20 throttle cable (the old one wasnt long enough? stupid chinese 80mm tb with no tps) custom piping made to get to the fmic, BOV is on that pipe about 200mm away from the fmic core (turbosmart dual port)

Also, needed a smaller battery so it wasnt in the way.

On a side note, a mate has put a plazmaman on his r33 (rb30/25) It fouls on the bonnet!!! I think this is only due to the extra 30mm height of the rb30 block but when buying a plenum beware of its height (if it runs on the standard runners) and be wary of the battery, buy a smaller one/rotate it for fiment

Link to comment
https://www.sau.com.au/forums/topic/317552-plenum-bov/#findComment-5195417
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...