Jump to content
SAU Community

Recommended Posts

Thanks David

No worries.

Like I said that is an approximate. Know of several (four other members!) others who have cc'd their heads and got 62cc or there abouts. Its fairly accurate "approximation" to assume yours will be the same.

If you're shooting for 9:1, just make sure your builder/assembler knows this and machines the assembly accordingly.

I think its weird that its not more commonly known (the chamber volumes)

I guess it comes down to not many people touching the heads on RBs and simply throw a bigger turbo and more boost at it to make power.

This also relates to CP/Weisco etc labling the comp ratios for pistons straight out of the box.

No worries.

Like I said that is an approximate. Know of several (four other members!) others who have cc'd their heads and got 62cc or there abouts. Its fairly accurate "approximation" to assume yours will be the same.

If you're shooting for 9:1, just make sure your builder/assembler knows this and machines the assembly accordingly.

wildo, costing me enough as it is, dont want to risk phucking it up. . :thumbsup:

Rb25 & rb26 I've seen all varied from 62-67. Neo's from 52-56. The first 20 thou ground off an un machined 25 & 26 head removes exactly 2CC's and it always varies from there

piston to deck heights varied too,

rb30 with rb25/26 pistons 10 - 40 under

rb30de pistons 20 thou under to 10 thou above

5 thou above will usually add .25 to the comp ratio

a 1.8 gasket replacing a 1.2 can lower the comp by around 0.75

  • 2 months later...

My RB30DET is running,

modified r33 25 head, drilled oil returns, welded water and vct, 20 inlet cam, 25 exhuast cam, full reco and skim.

RB30 block, drilled oil returns, drilled & taped tensioner, 1.0mm oil restristors, deburred and honed.

RB30 crank, grub screwed & crank collar, linish and balance.

RB30E std piston and rod, new rings, acl race bearings,

Cometic 1.2 MLS head gasket, genuine nissan gasket set.

N1 oil & water pumps, dayco 94407 timing belt, 2x tensioners.

Garret GT3071r 3037s 56t .63. ebay hi mount, tial 38mm gate, nismo 750cc, Freddy, apexi pfc, 3x pumps.

Heaps of Torque & 12psi @ 2500rpm :whistling:

Next: E85, reposition wastegate & tune

Edited by RED513

So just as I finish sorting out all the teething problems of the new setup and was thinking of booking it in for a tune.. some dumbass P-plater tries to make the gap and failed hard :(

The old girls heart will beat again soon, hopefully in the body of a sexy young 34 :whistling:

post-31803-0-66439500-1324344558_thumb.jpg

post-31803-0-09321800-1324344625_thumb.jpg

  • 3 weeks later...

New engine has just been tuned. I have a nice 300rwkw tune for pump fuel as thats plenty for the street. And a 475rwkw E85 tune at only 24psi as that seems the be the limit of my exhaust system.

It makes 180rwkw @ 4000 and 360rwkw by 4500 so things get fun pretty quick.

Just need a 4" system and a less restrictive muffler and should make more but this will do for now :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...