Jump to content
SAU Community

Recommended Posts

OK I have again booked us a hotel in Shepp for the upcoming DECA.

When: Fri 4 & Sat 5 June

Where: Tirana Motor Inn

Address: 33 -37 Wyndham St, Shepparton

Website: (if you wanna have a look) http://www.tiranamotorinn.websyte.com.au/

Cost: $50 per person per night

If you would like a room, please let me know as soon as possible, they will want to release to the public whatever rooms we are not using in a few weeks.

I need to know:

* nights staying

* how many people

* what bed configurations you need (ie twin, double etc)

If you are coming by yourself, that's fine, just let me know and I will team you up with somebody else to share a room with.

Dinner is booked at 7pm at the old Taco Baz establishment - now called Not Just Mexican!!

Let me know here, by email, by PM or by phone.

The sooner you tell me, the easier you make it for me.

Link to comment
https://www.sau.com.au/forums/topic/318940-deca-accommodation-fri-4-sat-5-june/
Share on other sites

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

People Staying:

FRI/SAT

Bec

Ryan

Mick

Tim

Russ, Tim, Campbell, Dean, Mark (2 x 1 queen/2 singles)

Shane J

Juliette

Dan (Halle) (double)

Brad + 1 (double) & Keiran (twin)

Beth & Dave

Brendan & Cass

Stagea Mick

FRI only

Hamish

Jimmy + 1 (twin)

Peter (Xrotor) + 3 (4 beds)

Leon

Mat (le fairy) Femino

SAT only

Ryan and Kathy

Extras for dinner Sat night

Gazelle + 10 :)

Luke & Anna

i'll talk to my mates about accomodation, iv'e got about 10 people coming this time, don't know if we will join the rest of the club tho, we like our motel down the road.

i'll get back to you one way or another, so you know how many seats for dinner.

dave

They're having us back????

what did you do ? my mates and i stayed sunday night too, and ahem piled 6 people into a 2 bedroom room. so glad i brang a sleeping bag and matress :)

At least we didn't put holes in doors :)

dammage ???? not cool

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...