Jump to content
SAU Community

And The Award For Worst M35 Bodykit Goes To....

rb26stagea
 Share

Recommended Posts

stagman Community Regular

stagman

Posted
Posted

haha dang, I thought i must of clicked on the wrong link, cause i liked it haha. IMO it just needs to have bigger wheels, be a different colour and lower and it would look good.

iamhe77 Grand Master

iamhe77

Posted
Posted (edited)
dolphin i reckon

Correct :(

I agree, I thought the whole idea of a body kit was to work WITH and ENHANCE the factory body styling and aerodynamics... something Dolphin clearly couldn't get their design team's head around for the NM35.

Mind you, the C34 Doplhin bodykits look just as bad (just more square)

Edited by iamhe77
Jetwreck Grand Master

Jetwreck

Posted
Posted (edited)

FFS....that's one ugly kit as is.....mind you I think what Stagman has said make sense....just needs some wheels and a decent ride height and it will look better. But never awesome.....I think I'm going to have nightmares tonight though!!!!

post-37023-1273011307_thumb.jpg

Edited by Jetwreck
pixel8r Mentor

pixel8r

Posted
Posted

oh i see the usual haters have turned up again...each to their own I say.

The front is too square, but the rest isn't too bad IMO. If you stuck the factory bodykit on the front (the one with the lip at the bottom) it may look ok.

atomaly Rising Star

atomaly

Posted
Posted

C34 Dolphin kits imho are the best looking kits about.

this M35 kit is however not very asthetically pleasing to me!

but then again. the M35 in general isnt either to me :thumbsup:

although the dolphin pics are somewhat better (other ones are shit angles) i found this on the dolphin site!

ph_m35-stagea_f.jpg

ph_m35-stagea_r.jpg

iamhe77 Grand Master

iamhe77

Posted
Posted
C34 Dolphin kits imho are the best looking kits about.

this M35 kit is however not very asthetically pleasing to me!

lol.... if you saw it front on, you would change your mind

(does let a ton of air through though)

GTRWAGON Enthusiast

GTRWAGON

Posted
Posted
C34 Dolphin kits imho are the best looking kits about.

this M35 kit is however not very asthetically pleasing to me!

but then again. the M35 in general isnt either to me :P

although the dolphin pics are somewhat better (other ones are shit angles) i found this on the dolphin site!

ph_m35-stagea_f.jpg

ph_m35-stagea_r.jpg

Nice rims :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...