Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Yeah you can't see what the back pressure is doing by looking at a dyno plot - sometimes it can show up as the power falling over prematurely due to the tuner having to pull timing to avoid detonation before MBT. Funnily enough this dyno plot looks like what you could expect to see in that case, if it weren't for the claim that the early drop off is due to wheelspin. Silly rolling road dynos...

Will be interesting to see how it goes on a hub dyno, and how the engine/turbo lasts at that power level if its going to be used on the track at the power level at all?

At face value, very nice power level and spool for a convenient and affordable package :blush:

Didn't Mafia make over 300wkw with a .63a/r GT3076R?

I think it was Geoff Raicer (of Full-Race fame) who once commented on a forum that torque starts declining when ex manifold pressure exceeds intake manifold pressure in a turbo setup. I guess this makes sense as it is at this point the VE would start declining resulting a drop off in torque and therefore hp. Hopefully the decline doesn't happen too rapidly resulting in a short torque/powerband.

The aim of the game is to get torque to build as early as possible and hold it flat to the redline - easier said than done with smaller responsive turbo's.

That was all the way to rev limiter. Drop off was mainly from lose of traction. Sam did not back off early. You can double check with Sam if you want.

The Main point is that we've managed to controll and hold boost all the way to 18psi using an internal gate setup on a .63 turbine housing.

and

This turbo has made the most power out of all the R33/34 high flows there are with 98 RON Fuel.

This is a very BIG claim that is untrue.

My car as a hiflow turbo form Adelaide Turbo Services and GCG and has made 298.2RWKW and couple of years ago and will be going back for a retune in a few weeks.

Cheers

NutR33

except your are runnning RB27 stroker and this is a RB25 stock. Also not been straped down.

strap down or hub result is going to be soo interesting to see. can't wait. :devil:

except your are runnning RB27 stroker and this is a RB25 stock. Also not been straped down.

strap down or hub result is going to be soo interesting to see. can't wait. :ermm:

+1 :D Cant wait to see more results!

I will be getting a high-flow done with tao so always good to see recent R&D

This is a very BIG claim that is untrue.

My car as a hiflow turbo form Adelaide Turbo Services and GCG and has made 298.2RWKW and couple of years ago and will be going back for a retune in a few weeks.

Cheers

NutR33

Has this been run on other dynos? or was it a one off?

I would also expect a bit more than 116mph from that power figure, been that Ive run and many others have too, 105mph with 180rwkws

Has this been run on other dynos? or was it a one off?

I would also expect a bit more than 116mph from that power figure, been that Ive run and many others have too, 105mph with 180rwkws

Just the same way 2 turbos can make the same peak output and completely different delivery, 2 tunes can do the same.

He might have the numbers, but might not have the torque to get the MPH down. The ET sounds about right for the car and MPH.

Torque wins races, pulling timing and fuel doesnt.

"This turbo has made the most power out of all the R33/34 high flows there are with 98 RON Fuel"

Sorry but i didnt see anywhere in his claims that it was the highest power figure on an RB25 or any other motor or level of mods.

  • 3 weeks later...

hey guys well i finnaly took this turbo of Toa, and let me tell you this its runs amazing!!!!!!!!!!!!! now all i need to do is get a tune!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...