Jump to content
SAU Community

Recommended Posts

Hi ya all,

It has been 6 months since the last pie run so i thought we should get back on the road once again. It will be same as the regular run that we do.

Meet at 10.00am at KFC carpark, Cross Roads, Casula.

Head off at 10.30am Sharp

Head down the Hume Hwy for a while then turn left as though we are headin to Woolongong.

Conitue along (dont veer into the gong just keep going straight)

Continue down the hwy until we reach a great big roundabout. Turn right at the round about and follow rd for a bit. Then turn right at the lights and follow it all the way up the mountain:)

Get to the mountain enjoy yummy yummy pies and check out each others cars:)

Distance: 115.8km Time: 1hr 19min (approx)

Travel: Fastest (with tolls)StartCrossroads Homemaker Centre

Continue along Hume Hwy, Glenfield36.5km8.

Veer left onto Picton Rd Exit, Wilton0.7km9.

Continue along Picton Rd, Wilton27.3km10.

Continue along Mt Ousley Rd, Cataract5.3km11.

Continue along Southern Fwy, Mt Ousley at University Of Wollongong18km12.

Continue along Princes Hwy, Yallah2.6km13.

At the roundabout - take the 2nd exit onto Illawarra Hwy, Albion Park Rail4.6km14.

At the roundabout - take the 2nd exit onto Illawarra Hwy, Tullimbar19.7km15.

Arrive at Illawarra Hwy, RobertsonSub Total 115.8km

1hr 19minEndIllawarra Hwy, Robertson, NSW 2577

I will keep a close eye on this and as we normally have quite a big turn out to this i will ask for a few drivers to nominate themselves as group leaders to ensure no one misses that turnoff that we seem to have problems with each time we head up there. I am hoping we get a great turn out and remember, All vechiles are welcome to come along just so long as they follow the ethics and rules that SAU promte at all times.

You have a whole 4 weeks to be planned and ready, make sure you take the time off work and put it on your calendars:):cool:

See you there

  • Replies 150
  • Created
  • Last Reply

Top Posters In This Topic

Ill also be letting the local police know that we are heading down on a friendly cruise and i will be asking for a gold coin donation from all drivers and the passengers as a donation to the RSPCA.

We shouldnt have troubles in this case:)




  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...