Jump to content
SAU Community

Recommended Posts

A low compression result = engine build time, it is the only real fix. It could be just a top end, but more like a complete build.

You need to get your mechanic to check it out and find the reason, could be that a dyno run will help pinpoint it.

I'd be surprised if its a compression problem, you would see things like oil burn, oil in the radiator, chooffing black and/or blue smoke everywhere, hard start from cold and etc etc etc

For mods etc check the dyno thread.........but nothing comes cheap = if you want more power you will need more $$$$$

first thing you need to do is get a compression test done, after that you can think of other things, a compression test is the easiest thing to try atm.

If you have a standard ecu and only 4 psi increase it should still be fine, i was running 15 psi on a standard ecu and it wasnt running badly.

ok cheers brett thanks ... how much is a comp test ? can any mechanic do it

also the question bout the boosting was directed at whether that says anything about compressin

Edited by havoc_r33gtst

dont know how much, depends on how much they charge per hour, any mechanic should be able to do it, best of finding one that has experience with skylines as it will help with other things in the future.

if ur compression is low it could be stuffed rings, valves, head gasket etc.. im having trouble with mine too when i turned the boost up it seemed like it made no difference and i heard a whistling sound on boost then i realised i have a boost leak on from my intercooler hoses on the front so hopefully longer hoses will fix it and hopefully ur car gets sorted soon

You are definately having issues due to NO ECU/TUNE.

Fact is one car might be fine @ 100psi, the next will get angry @ 10psi.

This is what your car is doing, simple as that.

Get some proper engine management going on, or back off the boost.

$550 for boost t and dyno?! :D

check basics, could be fuel pump too, hope the previous guys at least checked afrs

33gtst always freak out when u boost em up with light mods on stock computer

take it someone who knows these things, diagnosis on a dyno shouldnt take long :cool:

wow i think you got raped on the boost tee install and power run.... it was in no way a dyno tune anyway as i said before with my mods i made that power but if i run anything over 9psi i will drop mass amounts of power and i did up it to 11psi and made 140ish put it back to 9 and then it was back to normal.

try turning the boost down on boost controller to 8-10 see if that makes a difference then go over all your intercooler piping make sure you dont have a boost leak anywhere.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...