Jump to content
SAU Community

Recommended Posts

Dyno tune will be a while still when I'm ready to adjust the cam gears.Until then its road tuned

N1GTR.. Technically the only thing new about this is the actuators, and I'm sure if you purchaced -9 from gcg etc. they would put on the same 8.8psi actuator like what I got. Otherwise, same -1 / -9 / Gtss unit.

I think response can be tweaked further with the tune and also with boost control as there is no creep and very minimal spike(1psi) as is right now, so definately some gain to be have there, even if minimal.....and then there are cam gears

Have only been driving it a few days, but it does pull a touch harder on 13psi, But so far I'm satisfied that I have turbs capable of 300rwkw with stock like response.

Aaaaaah my bad!

Here's what I thought you meant;

http://www.turbobygarrett.com/turbobygarrett/products/turbochargers.html#medium

GT2854R - 471171-9

GT2859R - 707160-9

GT2859R - 780371-1

GT2860R - 707160-5

GT2860R - 707160-7

GT2860R - 739548-9

GT2860RS - 739548-1

GT2860RS - 739548-5

GT2871R - 472560-15

GT2871R - 743347-1

GT2871R - 743347-3

GT2871R - 707160-10

GT2871R - 780371-2

GT2871R - 743347-2

GT2871R - 743347-4

GT2871R - 771847-1

GT2876R - 705330-1

GT2876R - 705330-2

This is the last dyno tune I had, -9's, nismo pump, 555cc injectors, nismo AFM's, cam gears, stock engine.

post-12712-0-13533100-1318426627_thumb.gifpost-12712-0-59905300-1318426635_thumb.gif

Figures in all wheel killerwasps.

Since then I have fitted a different boost controller and the wastgates are now set to open at 16PSI with controller off.

Needs another tune to set boost controller and get rid of the drop in boost pressure. 22PSI tune to follow.

I'll let you guys know....

Aaaaaah my bad!

Here's what I thought you meant;

http://www.turbobyga...ers.html#medium

GT2854R - 471171-9

GT2859R - 707160-9....Gtss

GT2859R - 780371-1....Gtss with act

GT2860R - 707160-5.....2530

GT2860R - 707160-7....R34 N1

GT2860R - 739548-9

GT2860RS - 739548-1

GT2860RS - 739548-5

GT2871R - 472560-15

GT2871R - 743347-1

GT2871R - 743347-3

GT2871R - 707160-10....Gtrs

GT2871R - 780371-2....Gtrs with act

GT2871R - 743347-2

GT2871R - 743347-4

GT2871R - 771847-1

GT2876R - 705330-1

GT2876R - 705330-2

post-42272-0-02044400-1318454661_thumb.png

:thumbsup:

I guess they didn't say anything about injector duty.

I was seeing roughly 90% on a cold night with 22psi peak in the midrange through to 17psi or so at the top end. Rich enough to see black out the back on full boost :whistling:

Stock fuel reg too....

Should be okay, guess I'll find out.

Well since there is NO info on this here I just thought i'd put this up and update as I go along.

The comparision below is results for the -1 turbo which is the -9 that comes with a 8.8psi actuator from Garrett, compared to stock R33 Gtr turbos.

post-42272-0-01856100-1318371152_thumb.png

The top window is the -1/-9 which reaches the same level of boost(13.3psi) about 200-300rpm later than the stocks, and the car drives basically the same as before.

The ONLY thing changed was the boost level was raised only one notch on the controller (profecb2) to get the same level for comparision....start/gain etc was left the same and the pfc tune was untouched.

My boost control kit reads 1psi low for some reason, hence 13.3psi

Ignore the scale on the bottom as this would be different due to the length(secs) of each log

Well with two turns in on the actuators I was able to get it down to stock like response, well on paper at least....To me it feels even better than stock coming into boost

post-42272-0-75110700-1318977532_thumb.png

Top -1/-9, bottom is stock

Is boost creep the only thing to look for with too much preload? I want to shorten them some more :yes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...