Jump to content
SAU Community

Recommended Posts

I have blown 3 MAFs in about 7 months, I have heard they are a weak point however I think I may be killing them a bit easier than I should be able to. I have concluded that all three times that I killed them I was at redline in triptronic mode. I can drive it hard when its in auto without any problems. Should this happen if I redline or is there something else that could be causing this?

The only mod I have on the car is a straight through 3" exhaust, other than that its factory.

I don't have the power duct open and never have.

Any help would be appreciated.

ps. Whats the best Maf to get for these instead of paying $340 bucks to nissan?

2003 Stagea 250t rs Four

Link to comment
https://www.sau.com.au/forums/topic/323437-my-maf-murdering-problem/
Share on other sites

Not sure I know any answer to your problem but I can tell you that at redline the MAF is putting out between 4.77 - 4.88v, even on a stock car.

So the MAF is only just capable of keeping up with the motor. I am not sure that even going to 5.0v is going to ruin your MAF but what it should do is create a big back fire as the motor retards and dumps fuel into the cylinder to protect the motor.

Cheers

Andy

There are a few Maxima ones on ebay at the moment, not sure if they are the same but this seller has three for sale. They certainly look the same.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

Must say it sounds a unique problem! I don't know the answer either but if you replace the MAF with a different unit with different values you will need to retune the ecu which in your car is still, to my knowledge, impossible.

If you are planning on any more mods some sort of piggyback such as e-manage would enable you to tune a bigger maf if that is going to fix your problem.

you can cut out the silicone out from the top to expose the board inside

what happens in the old nissans is that the pins where the plug comes in gets fractured and you get a dry solder joint

just a touch from a soldering iron and a dab of solder and they are all good again

not sure if its the same for the m35's but if your killing them at this rate it could be worth looking at

There are a few Maxima ones on ebay at the moment, not sure if they are the same but this seller has three for sale. They certainly look the same.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

My maf has 5 pins in it the maxima ones only have 4 pins. Also I have no markings or model numbers of any kind on my maf. Someone couldn't possibly give me the numbers off of theirs so I can try and find a match online?

OMG! 3 in 7months that f....d!

Maybe a bare wire in the loom touching metal somewhere.

Check out Mr Muffler, see if they can order a bosch one, think they are about $300.

My r31 (rip) was 20 years old before anything crapped itself, 1st the MAF, TPS then some other things.

Pretty sure mine was related to a high pressure spray :cool:

Edited by Stagea_Neo
Emanage ultimate with a map sensor will do the trick...

I don't think these units can be repaired when they fail, I have tried. Definitely not a dry joint on the board.

Thanks for the help, What sort of money did it end up costing you to install the Emanage? Did you do the install yourself or get someone else to do it? Also what model Emanage do we use with the m35?

Cheers

OMG! 3 in 7months that f....d!

Maybe a bare wire in the loom touching metal somewhere.

Check out Mr Muffler, see if they can order a bosch one, think they are about $300.

My r31 (rip) was 20 years old before anything crapped itself, 1st the MAF, TPS then some other things.

Pretty sure mine was related to a high pressure spray :blink:

i'd agree with Pete, a bare wire or a short in a loom plug or ecu could be frying them. i'd test and inspect the wiring, or get someone to test it, before putting another one on and blowing it up too.

the chances of having 3 AFM's with dry joints is pritty slim. i haven't really heard of anyone with that problem on a M34, it more of a problem on the older RB series motors.

i'd agree with Pete, a bare wire or a short in a loom plug or ecu could be frying them. i'd test and inspect the wiring, or get someone to test it, before putting another one on and blowing it up too.

the chances of having 3 AFM's with dry joints is pritty slim. i haven't really heard of anyone with that problem on a M35, it more of a problem on the older RB series motors.

Thanks guys, I have had a quick look at the wiring the first time it happened but i'll have to get the multimeter into and have a really good look.

Just out of curiosity what happens when you redline in your m35s?

I used to get a close up view of the windscreen, with the emanage I get a smooth 7000 rev limiter.

Is your emanage install and tune all done and finished now? I am seriously considering going down this path, if I do would you mind discussing in depth further? I have to find someone here who is confident to do the tune.

Its all running but will never be finished. Evolving more describes it. :domokun: I like being able to adjust and monitor everything myself. (I hope to be able to tune it myself one day.)

If you go the Emanage route, you will definitely need to find a competent tuner to do the install.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...