Jump to content
SAU Community

Recommended Posts

Hey

Lately my oil pressure gauge has been getting pretty low from time to time and other times it will be normal and fine, sometimes it even drops down so low and then goes back to normal during a 1 hour trip.

I have a photo of the pressure gauge at its lowest which was only 2 days ago, and since it hasn't had the issue but it does come and go and im not sure if I should be worried or not, any opinions or suggestions would be helpful.

oilpressure.jpg

Link to comment
https://www.sau.com.au/forums/topic/323782-r34-oil-pressure-low/
Share on other sites

common problem for the fuel pressure sender/switch to play up, replace that and you should find that your reading will return to what it should be.

its located near the oil filter

ive circled the oil pressure sender in red in the pic below

img0032ch2.jpg

if that fails then it looks like ur oil pump is quite worn..

Hey

Lately my oil pressure gauge has been getting pretty low from time to time and other times it will be normal and fine, sometimes it even drops down so low and then goes back to normal during a 1 hour trip.

I have a photo of the pressure gauge at its lowest which was only 2 days ago, and since it hasn't had the issue but it does come and go and im not sure if I should be worried or not, any opinions or suggestions would be helpful.

oilpressure.jpg

Have you checked your oil lately..??

not milky..???

I have this exact same problem with my R34 GTT ... I reckon its a faulty sender unit. I asked Nissan how much for a new one and from memory it was close to $200 yikes :P

but it's been bugging me for so long now I might just try get one from the wreckers just to see if its the actual sender unit (provided I don't get another lemon from the wreckers)

How hard is it to remove/replace one of these sender units through the engine bay ? would be a real pain in the bum hey ? the whole thing that you circled in red has to be unscrewed yes ? would oil leak out when you unscrew it?

  • 1 year later...
  • 5 months later...

Hey

my r34 GT has the same thing, when its cold it sits about 5 ish and when its warm and just idle it will sit around 1 ish but will go up when you start to drive ??

freaked me out as well when i first seen it , so is this anything to worry about ? thanks guyz

That's normal. The hotter the engine is, the more oil will thin out resulting in less oil pressure. So on a cold start oil pressure will be very high. On operating temp it'll probably be around a quater of what the pressure is on cold start.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How dare you sell your unreliable Skyline and buy a reliable, Toyota/Yamaha car with a strong gearbox, torsen LSD and Toyota reliability. At least you won't need to worry about oil pumps, big catch can, oil restrictors, blowing off power steering belts, sheering off 3rd gear, failing ABS relays/pumps, etc.
    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
×
×
  • Create New...