Jump to content
SAU Community

Recommended Posts

I have an R34 GTT, current modifications i have on my car are intercooler, exhaust, Bosh 040 fuel pump, pod filter (boxed) & Boost controller.

I'm booked in for a tune on friday, i was hoping to get about 250rwkw from my car.

Any recommendations on what other mods i need to achieve my goal.

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/
Share on other sites

I have an R34 GTT, current modifications i have on my car are intercooler, exhaust, Bosh 040 fuel pump, pod filter (boxed) & Boost controller.

I'm booked in for a tune on friday, i was hoping to get about 250rwkw from my car.

Any recommendations on what other mods i need to achieve my goal.

Thanks in advance.

A bigger turbo and an ecu

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5279971
Share on other sites

Should've got all the parts before the tune. Generally you need:

550cc injectors

Z32 AFM

Boost controller

3inch metal inake pipe with good pod filter

3inch exhaust with Honey con cat

High flowed turbo

Strong clutch

fule pump

Nistune or better ECU

Feed it with BP ulitmate.

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5279975
Share on other sites

the "tune" you have done on friday is going to consist of the workshop driving the car onto the dyno, doing a run or 2, possibly playing around with the boost level, doing another dyno run and then driving it off again. the stock ecu can't be tuned.

and as has been said above, you are going to fall short of your goal of 250kw by about 50kw.

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5280341
Share on other sites

and as has been said above, you are going to fall short of your goal of 250kw by about 50kw.

...or more. With a standard ECU you'll probably hit rich and retard (as i did) eventually which makes the car a pig. I managed 185rwkw with exhaust, pod and 13psi.

With an aftermarket ECU and Z32 afm (or a better ECU with 3bar map sensor ie Haltech) you might be able to make 210+ on the standard turbo, although don't expect it to last all that long at that power level...

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5280687
Share on other sites

You'll need a credit card...............with approx. a $5000 limit.

Then you can buy all the necessary hardware!!!

At least...! I just dropped $12k on my R34 to make 273kw, although that was with an expensive ECU and other parts and it has plenty more left in it for E85...

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5280710
Share on other sites

I reckon you would pull around 200rwkw ... you need the turbo +and both aftermarket ECU and Injectors

I'm voting 180-190(ish) tops.

Fuel pump and intercooler will make exactly zero difference to power and as i mentioned my 34 made 185rwkw with some boost, pod and exhaust.

Of course Dynos do all read different - 200 on one is 180 on another...

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5280787
Share on other sites

I'm voting 180-190(ish) tops.

Fuel pump and intercooler will make exactly zero difference to power and as i mentioned my 34 made 185rwkw with some boost, pod and exhaust.

Of course Dynos do all read different - 200 on one is 180 on another...

not quiet true. fuel pump won't do squat for power, but as you start doing other mods then you need a better fuel pump to be able to flow enough fuel to stop it from leaning out.

as for the intercooler, they can make you get higher power than the stock one. the reason being that if you give the car a bit of a fang on the way to the dyno then the stock side mount cooler will already be suffering from heatsoak (therefor higher intake temps and less power) before it even goes on the dyno. a bigger intercooler will stay cooler for longer and therefor give you higher power on the dyno (as well as on the road). it doesn't take long for the stock cooler to heat up after you have given it a boot a few times, while in the colder days we are having at the moment a fmic will stay cool for much much longer.

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5280956
Share on other sites

not quiet true. fuel pump won't do squat for power, but as you start doing other mods then you need a better fuel pump to be able to flow enough fuel to stop it from leaning out.

as for the intercooler, they can make you get higher power than the stock one. the reason being that if you give the car a bit of a fang on the way to the dyno then the stock side mount cooler will already be suffering from heatsoak (therefor higher intake temps and less power) before it even goes on the dyno. a bigger intercooler will stay cooler for longer and therefor give you higher power on the dyno (as well as on the road). it doesn't take long for the stock cooler to heat up after you have given it a boot a few times, while in the colder days we are having at the moment a fmic will stay cool for much much longer.

The fuel pump will only help once you reach the limit of the standard system (as you say) which won't be happening here.

The cooler - well it may help in the situation you described, true - but usually i'd assume the car would be sitting around, run a couple power runs and that's it, with a fan blowing into the engine bay. This is not a proper 'tune'. It can stop power loss through heatsoak / high inlet temps yes, but it's not going to give you more power per se.

Essentially what I meant was your not going to get an extra XXkw with those two mods... :D

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5281075
Share on other sites

The fuel pump will only help once you reach the limit of the standard system (as you say) which won't be happening here.

The cooler - well it may help in the situation you described, true - but usually i'd assume the car would be sitting around, run a couple power runs and that's it, with a fan blowing into the engine bay. This is not a proper 'tune'. It can stop power loss through heatsoak / high inlet temps yes, but it's not going to give you more power per se.

Essentially what I meant was your not going to get an extra XXkw with those two mods... :domokun:

and i pretty much agree

Link to comment
https://www.sau.com.au/forums/topic/323983-urgent-help/#findComment-5281229
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah it is always worth testing and balancing actuators out of the box, just set the pressure regulator on a compressor very low (eg 5 psi) and increase it slowly to see when they both move.....unfortunately while you may be able to adjust the length of the actuator rod to minimise any difference, the actual pressure they move from is not adjustable so you need a well matched pair. And yes, the VCAM is probably contributing; the earlier in the rev range they come on boost and the slower the revs build (I think your demo was in 5th), the more you notice it.  Driving at WOT through 1st, 2nd, 3rd etc you will probably never hear it as any shuffling starts and is over super quickly
    • oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
×
×
  • Create New...