Jump to content
SAU Community

Recommended Posts

Hey guys,

Just putting in a set of GT-SS turbos on a GTR. Any advise on what the minimum psi the adjustable actuators can be set to and how do you know if they are set equal.

Looking at running a low boost setting of around 10 psi and a hight boost (via manual bleed valve at the moment) of 18psi.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/324717-ajustable-actuators/
Share on other sites

the way i set mine with out actually driving the car was to use a vaccum/pressure pump with a pressure gauge. i just kept adjusting the linkage out untill it had the amount of preload needed to open at the amount of boost i wanted to run. this way is much easier than driving and adjusting repeatedly untill you get what you want.

the way i set mine with out actually driving the car was to use a vaccum/pressure pump with a pressure gauge. i just kept adjusting the linkage out untill it had the amount of preload needed to open at the amount of boost i wanted to run. this way is much easier than driving and adjusting repeatedly untill you get what you want."

um that will not work . the gates need to be fully open at the psi you want .

as hyper gear said . waste gate preload is not really the way to adjust overall boost pressure . it works to an extent but only for maybe up to 5 psi(roughly maybe more or less) over spring pressure as anymore than this and you are going to start limiting waste gate travel and will end up with boost creep(boost climbs with revs as gates cant flow enough)

yes running an ebc over waste gate spring pressure to achieve the same level of boost can provide faster spool up but in the real world you will probably find the difference is not worth it

They would normally be set at 7psi. the average pre-load should have on the actautor is 3mms. You then need to use a boost controller to increase overall boost sittings.

What kind of advice is that? an adjustable actuator's preload should be set to a point where the boost curve just starts to spike...then backed off half to a full turn...then thats the optimum preload for the setup...then overall boost can be raised via a boost controller...you can't just say an average of 3mm...coming from someone who sells turbos i'd expect at least some accurate info...

What kind of advice is that? an adjustable actuator's preload should be set to a point where the boost curve just starts to spike...then backed off half to a full turn...then thats the optimum preload for the setup...then overall boost can be raised via a boost controller...you can't just say an average of 3mm...coming from someone who sells turbos i'd expect at least some accurate info...

That point is precisely 3mms with .5 bar actuators. Try it your self if you don't believe it .

I have GTSS's with the original HKS actuators, f*kn things run 0.5bar on mani pressure - must not all be 1bar...

Their adjustable range is stated as 0.8kg/cm2 - 1.6kg/cm2 - about 11psi to 22psi. Not sure why you are only getting half a bar - you may be right there might have been a different series.

So maybe set them to about the middle of their adjustability - and run them up on the dyno cautiously. I've never changed them on the vehicle before but can't be too hard to get to.... surely :P

It would be worth checking they're set the same by applying pressure to the common line at the boost controller and verifying they both open at exactly the same pressure before you re-install all the bits you've taken off to get at the adjustment.

I've noticed that new hks actuators often seem to be a bit weak, making it a soft coming onto boost. the supplied one with my gt-rs sucked at anything over 1 bar, changed actuator one week later. if u wanna run decent boost ie 15+ psi maybe get stiffer/higher rated ones.

1 bar on gt-ss's is barely getting out of bed :D

  • 1 month later...
I have GTSS's with the original HKS actuators, f*kn things run 0.5bar on mani pressure - must not all be 1bar...
Their adjustable range is stated as 0.8kg/cm2 - 1.6kg/cm2 - about 11psi to 22psi. Not sure why you are only getting half a bar - you may be right there might have been a different series.

So maybe set them to about the middle of their adjustability - and run them up on the dyno cautiously. I've never changed them on the vehicle before but can't be too hard to get to.... surely :)

umm mine are the 0.5bar variety as well although im looking at running them at 18psi or so.. not sure if it allows that much adjustment but whats the best way to set em while in place.. adjust both and check with a pressure gauge when both start to open??

  • 2 weeks later...
Their adjustable range is stated as 0.8kg/cm2 - 1.6kg/cm2 - about 11psi to 22psi. Not sure why you are only getting half a bar - you may be right there might have been a different series.

So maybe set them to about the middle of their adjustability - and run them up on the dyno cautiously. I've never changed them on the vehicle before but can't be too hard to get to.... surely :/

HKS site states 78.5~108kPa(0.8~1.1kgf/cm2) for the GTR - 1430-RN001 which would mean 11psi to 15.6psi

should i have boost drop issues even with these heavy duty actuators or should i be looking else??

air leaks test done (intake manifold gasket replaced) and boost controller by gizzmo ms-ibc

post-40640-1280380092_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...