Jump to content
SAU Community

Recommended Posts

I was looking at purchasing a gt2835pro S kit for mt rb25det neo, upon ordering it they told me its not made anymore and they can send me a gt2835kai, which i assume you dont get a dumppipe. Just not sure what else is differnt with the kit for the turbo itslef?? any help?? cheers

Link to comment
https://www.sau.com.au/forums/topic/327087-gt2835pro-s-vs-gt2835kai/
Share on other sites

I was looking at purchasing a gt2835pro S kit for mt rb25det neo, upon ordering it they told me its not made anymore and they can send me a gt2835kai, which i assume you dont get a dumppipe. Just not sure what else is differnt with the kit for the turbo itslef?? any help?? cheers

on the HKS website it still says it comes as a kit, but I think the Kai version is now using the twin scroll version...

slight power increase going by what the translated HKs page says...

I have a used HKS2835pros turbo for sale with exhaust flange if your interested

The 2835 has always confused me slightly, its seems so close to the GT-RS that its place in the market isn't really required? They share the same compressor wheel, with a slightly bigger rear housing correct? Obviously HKS's graph proves the difference between the kits is minimal, to say the least.

The 2835 has always confused me slightly, its seems so close to the GT-RS that its place in the market isn't really required? They share the same compressor wheel, with a slightly bigger rear housing correct? Obviously HKS's graph proves the difference between the kits is minimal, to say the least.

I would actually say by looking at the graph that the GT-RS is redundant...

But also the difference between the pros and kai is pretty much nothing in performance, the kai should whistle like a bitch with that front cover though

The Pro S is close to the RS, but seems to have a marginally bigger top end. It is squeezing in between the RS and the 3037 in the HKS range. All three have been around now for quite a few years.

The Pro is the difference, external WG etc etc.

Not sure if you can still get the Pro now though?

I would actually say by looking at the graph that the GT-RS is redundant...

But also the difference between the pros and kai is pretty much nothing in performance, the kai should whistle like a bitch with that front cover though

I agree, judging by the graph the GT-RS should be dead in the water.

  • 3 weeks later...

As far as I know no one is doing a "T3" flanged twin scroll twin integral gate turbo so far .

I doubt this situation will last forever since Mitsy has done so well with turbos like this , except in their own flange pattern . Actually HKS is now doing a bolt on BB TS TIG turbo for the Evos 4-9 and its supposed to be a nice if expensive unit .

It looks to me like Garrett is being left behind with wheel designs and trims and it remains to be seen if they'll do anything about it . Slightly larger wheels and or smaller trims is working better for the other turbocharger manufacturers and when you throw in TS turbine housings and port shrouded compressor housings they can be wider ranging things .

A .

You wouldn't happen to know if there's any difference in specs? Externally it just looks like there's anti surge slots, and that's about it!

Assuming you are friends with the OP, did the KAI come with a dump or is it an OEM bolt up scenario?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...