Jump to content
SAU Community

Recommended Posts

my old R33 GTS-T had misfiring issues from day one... could not even cope with 180rwkw... Splitfires were the fix for it...

my current car R33 GTR is now putting out 270kw at the wheels with the standard coilpacks... no spark issues at all

"if it aint broke, dont fix it"

There is a shortage of hard evidence on coilpacks.

The stockers have the track record.

Splitfires are getting a track record over a few years now.

I have bought a set of Yellowjackets on the basis of bench tests i have seen but they still have to prove the lasting qualities.

The red ones appear to be lesser quality but again time will tell.

I had a similar issue ~ 18psi (250rwkw mark) and the new coil packs resolved the problem.

Running 18psi initially was ok on the original coil packs, replaced spark plugs, tried the silicone coating which helped slightly but the misfire came back.

Ended up buying the yellow jackets and the problem has gone. When I get new spark plugs I'll buy the ones gapped at 1.1mm (against 0.8mm) now and see if the spark still holds.

Last post in here covered it

http://www.skylinesaustralia.com/forums/Gc...20&start=20

Edited by benl1981

Well I dunno what your car setup is, but usually when a person runs an atmo bov on a stock ECU it will run a bit richer on gear change and cause a bit of a pop/backfire through the exhaust.

whats the silicone method? smear house grade silicone around what part of the coil? what are the first signs of missfire on a 25det with only breathing mods that runs std boost?

first signs of a missfire would probably be the missfiring, under max boost between 3-5k rpm, or randomly cutting out and having popping sounds like a wrx until you either turn the engine off or it fixes itself. ive had both.

i was trying to find the coilpack silicon-ing diy but didnt manage it, same principle as these

http://www.skylinesaustralia.com/forums/Fi...=coilpack+clean

http://www.skylinesaustralia.com/forums/Mi...500-t32356.html

Edited by Galois

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...