Jump to content
SAU Community

Recommended Posts

My R34 GTT has been misfiring even more since I turned the boost up to 10psi, finally got a chance to take her apart, wanted to check the coilpacks to see if they had any cracks in them.

Found out they a splitfires so pretty stoked about that, but as I started going through each one to check them and also check the plugs I noticed a lot of oil sitting above two of the coils.

post-72359-1278389750_thumb.jpgpost-72359-1278389782_thumb.jpg

Anyone had this issue before? I'm pretty sure it's oil, if it were petrol I would be able to smell it.

And is it safe for me to clean up the oil then take the coilpack out to check the plugs? scared I might get crap inside the cylinder head.

Thanks in advance!

Jaylon.

Link to comment
https://www.sau.com.au/forums/topic/327765-oil-leaking-onto-coilpacks/
Share on other sites

Oil in the cylinder head won't be the end of the world - anything that's collected in this oil will be.

Could be rocker-cover gasket leaking....degrease it, hose it out, let it dry (perhaps even assist it with a compressor) then remove them.

Cheers,

Got stuck into it again yesterday, I used paper towels to soak up most of the oil.

Looks like the guy that sold it to me lied about putting in new spark plugs just before i bought it haha.

It's so dirty in there I doubt any mechanic had been under there in a couple of years ay.

Cheers,

Got stuck into it again yesterday, I used paper towels to soak up most of the oil.

Looks like the guy that sold it to me lied about putting in new spark plugs just before i bought it haha.

It's so dirty in there I doubt any mechanic had been under there in a couple of years ay.

when you replace the plugs, gap them to .8mm (i kow this is right for the 33, not too sure bout the 34) and should help the missfiring. but clean all the crap out before you do the plugs, dont want anything falling into the holes for the spark plugs.

Found out they a splitfires so pretty stoked about that, but as I started going through each one to check them and also check the plugs I noticed a lot of oil sitting above two of the coils.

...

Anyone had this issue before? I'm pretty sure it's oil, if it were petrol I would be able to smell it.

And is it safe for me to clean up the oil then take the coilpack out to check the plugs? scared I might get crap inside the cylinder head.

Hey mate, I had a similar issue with my R34. It could be the rocker cover gaskets but could also just be spillage from a careless oil change.

I cleaned mine up best I could before pulling the plugs out to prevent crap falling into the cylinders. My plugs are also gapped down to 0.5mm now as my coil packs on their way out, I will regap them to 0.8mm once I get a new set. Some further tips on resolving a misfire here.

Thanks, Yer I cleaned it all up pretty thoroughly.

Changed all the plugs as well and now there's no misfire!

The car blew the tiniest bit of smoke from the oil when I first started it but now it's all good.

Half a mission just getting into the plugs tho, I'll check it again in a couple of weeks when I have some more money whether I'll replace the rocker cover gaskets.

replaced my own rocker cover gaskets due to a leak, the gaskets and half moon seals from memory cost about $80 all up (both rocker cover gaskets and 2 half moon seals) and its a few hours work if you are comfy doin it yourself, else you shouldn't pay more than about $150-200 for labour if you cant do it yourself

Before you get all carried away replacing gaskets.....

....a screwdriver is your friend.

Tighten up any loose cam cover screws.

Good idea! I'll check for loose screws, if that doesn't fix it I'm able to replace the gaskets myself.

Yeah they are cheap, but I lost too much money at the casino this pay haha.

Can't wait till tax return, gonna finish off the exhaust with dump and front pipes, high flow cat, and FMIC :D

The gaskets will be fine, they are rubber and given the age of your car will still be fine. As has been said, retighten all the bolts holding the camshaft covers on. With heat they tend to loosen a bit over time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...