Jump to content
SAU Community

Recommended Posts

Hey Everyone,

As you can tell by the title of the thread I'm new to the world of imported motor sport and more importantly skylines. I am currently own an Si Honda prelude and am looking to upgrade. So I am looking for an R32 two door for around 10k to be bought at the end of the year.

I would love whatever advice or tips you could give me as I search for my new car :wub:

Cheers,

OB

Link to comment
https://www.sau.com.au/forums/topic/328020-new-to-the-world-of-skylines/
Share on other sites

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

you may get a 32 gtr for 10k but i wouldnt expect it to be in very good condition. but you never know what will pop up.

interior is a lot newer looking in the 33, engine is easier to get power out of, gearbox is stronger, some people dont like the styling.

just go look through the for sale section, see what you can find.

i wouldn't buy any GTR for 10K! most likely it'll leave you disappointed as you'll probably need to sink big dollars into it just to get it going properly! most guys i know who own R32's eventually put the R33 motor and gearbox into them anyway! if it was me, i'd go the R33, but i am biased. however you cant ignore the fact of the much better, stronger and more reliable motor and gearbox the R33 has compared to the R32. the R33 also has bigger brakes (same as R32 GTR) which also makes a big difference.

just do some research, take your time and figure out which one you'd prefer. plus, my R33 will be for sale towards the end of the year :thumbsup:

i wouldn't buy any GTR for 10K! most likely it'll leave you disappointed as you'll probably need to sink big dollars into it just to get it going properly! most guys i know who own R32's eventually put the R33 motor and gearbox into them anyway! if it was me, i'd go the R33, but i am biased. however you cant ignore the fact of the much better, stronger and more reliable motor and gearbox the R33 has compared to the R32. the R33 also has bigger brakes (same as R32 GTR) which also makes a big difference.

just do some research, take your time and figure out which one you'd prefer. plus, my R33 will be for sale towards the end of the year :thumbsup:

R32 gtst type m has R32 gtr brake calipers on them, just not the front rotors. also to R32 wheel base is about 100mm shorter (overall the R32 gtst is a smaller car)

i wouldn't buy any GTR for 10K! most likely it'll leave you disappointed as you'll probably need to sink big dollars into it just to get it going properly! most guys i know who own R32's eventually put the R33 motor and gearbox into them anyway! if it was me, i'd go the R33, but i am biased. however you cant ignore the fact of the much better, stronger and more reliable motor and gearbox the R33 has compared to the R32. the R33 also has bigger brakes (same as R32 GTR) which also makes a big difference.

just do some research, take your time and figure out which one you'd prefer. plus, my R33 will be for sale towards the end of the year :thumbsup:

Haha, I'll keep my eyes open for it then :D

Cheers for all of the info and advice. I'll do my research and see what is around when I'm all good to buy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...