Jump to content
SAU Community

Recommended Posts

Hi there,

I'm looking at purchasing a Haltech Platinum Pro plugin ECU for my R33 gtr and i'd like to obtain clarification whether the ECU will support the factory AFM's or totally rely on the MAP sensors. I vaguely recall reading that it can support both but i'd like to find out for certain.

In this respect, does the ECU operate or perform better under a particular setup e.g performance/economy wise? I realise this may trigger a wide debate but it would be good to obtain people's experiences and setups relating to this ECU.

Thanks,

Adrian

Link to comment
https://www.sau.com.au/forums/topic/328670-haltech-platinum-pro/
Share on other sites

I think i may have found the answer to this from haltechs site

"Supports R32 GT-R twin MAF sensors" and " Selectable onboard internal MAP sensor rated to 150kPa (up to 1.5 Bar or 22psi boost)"

So i take it will support the twin afm's. Does anyone recommend the AFM approach over the MAP setup? Im generally looking at keeping the factory airbox thats why im keen on checking if its the preferred approach.

Thanks

An ECU is only as good as the person tuning it. Talk to your tuner and see what ECU/sensor setup they recommend.

The Platinum pro does support twin AFM's, it also has the option of an internal or external MAP sensor.

I have one in my R33 GTR, using the onboard MAP sensor, cold starts are great, idles perfectly, power wise its making 320kws on a run in tune, not sure on fuel economy as I've only put a few hundred kms on it since the run in.

Cheers,

Johno

Many thanks guys, this is exactly the type of information i was after. I should really get in contact with my tuner and Haltech direct.

Johno, you mention the internal MAP is working well in your setup. I'd be looking at a similar power figure (is that with the N1's?), but basically what i take from their site is the onboard unit would be efficient to 22psi. I think that is more than adequate on a standard internal engine. Obviously pushing more you would need to revert to the optional MAP sensor.

I think i also have read that the ECU supports two ignition/fuel maps, making it possible to switch between two tunes?

Cheers

Adrian

No probs, Its working quite well. I will be swapping over to external map shortly and turning up the boost. That's correct 2.5 Bar internal is supported. Im running 2530's but N1's (GTSS or -7's) will get you into that power range with a bit more response.

Yep, you can load maps quite easily. I aim to have 2 maps done, one for street (98 octane & fuel economy lol) and one for E85 when its more consistent & readily available.

Cheers,

Johno

My thoughts exactly johno.

Switching between the two maps; is it as simple as loading up from the laptop? I doubt it would have some sort of an external switch that would allow this, though it would be ideal!

In regards to knock control, i couldn't see anywhere in the spec's whether the unit responds to knock by say reducing power or rev's?

Cheers for the responses they have been helpful :)

You wil have to load via laptop for now.

Live Dual Mapping - Not yet, but I have been told its only a firmware update or 2 away, probably about 2-3 months.

The Pro series does full knock control, long term and short term trimming. It also does long term and short term Fuel control.

It will flash the engine check light each time a knock even occurs and even log it if you like.

  • 1 year later...

And without starting a new topic, are these plug and play into the rb25det series 2? They sound more functional than a power fc... Whats the price on one of these?

Auto tune mmmm. There is an auto tuner for power fc but I ain't have the gonads to try it out. All it needs to work is the wide band and some limits entered by the user. I think it should be an option, its nothing fancy really. Have the ecu know what car its on and let it load up some target afr's and start adjusting til they are met from the wideband feedback. After fueling, give timing until a threshold of knock is heard. Then the user can go over it to adjust anything if necessary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...