Jump to content
SAU Community

Recommended Posts

So I've been soaking all my dirty parts in degreaser and scrubbing with a friggin toothbrush saying "well it's only one time, just do it" but it seems like every now and then I have to do it again. I use the 'export quality' degreaser as well as the 'kenco heavy duty' one @ 2:1 ratio water:degreaser (it's their most concentrated recommendation but I have used it straight) which is ok for regular stuff but doesn't do much for the fun stuff until I scrub... hard.

I CBF spending so much time hitting it with a brush so to futureproof myself, do you have a better method?

So I've been soaking all my dirty parts in degreaser and scrubbing with a friggin toothbrush saying "well it's only one time, just do it" but it seems like every now and then I have to do it again. I use the 'export quality' degreaser as well as the 'kenco heavy duty' one @ 2:1 ratio water:degreaser (it's their most concentrated recommendation but I have used it straight) which is ok for regular stuff but doesn't do much for the fun stuff until I scrub... hard.

I CBF spending so much time hitting it with a brush so to futureproof myself, do you have a better method?

there is an industrial degreaser from bunnings that i found was the best on the retail market - $60 for 15L and is green/yellow in colour

simple green works well also in high concentrations - and available from bunnings

both these need soaking though - so overnight in a tub and then pressure hose them off.

another handy household cleaner for baked on oil is oven cleaner left on for about 5-10 mins the hosed off.. can help to scrub this a little also but works wonders (dont leave on too long or it discolours alloy)

ive always used motorspray degreaser and cant say ive even thought about complaining about its strength.

its the stuff u get at paint shops in 4L. i just apply it with a paintbrush, sometimes it needs some work with the brush then just wash off with a hose.

can i just ask what you are actually asking here? are you asking for a better degreaser to make it so you don't have to scrub it as much to get it clean, or are you saying that you clean the parts and then a little while down the track they get dirty again?

if it's for the scrubbing bit, stuff that is really caked on will usually need a bit of scrubbing. you won't really find too many products that actually eat through seriously caked on crud. for this stuff you are best off giving it a light soak (few mins), then giving it a bit of a scrub then soaking it again and then a final scrub if needed. this way when you scrub it then soak it for the second time you are allowing the degreaser to penetrate more.

A better degreaser or method to clean so I don't have to scrub it as much.

I've had a few gearbox conversions go through on my car and every time I'd be there scrubbing away at the new gearbox saying "it's only once"... turned out to be 3 'onces'. I recently got some GTR32 brakes so was scrubbing them and I know these brakes won't last me... I can see myself scrubbing once again and I'm already dreading it.

Thanks for the ideas, I'll give those suggestions a try next :D

Now what to do with 4L of crappy new kenco degreaser.. hmm...

if it is alloy that you are cleaning, try getting some alloy cleaner. it's a chemical that you mix with water and it cleans alloy really well. don't think it does much on steel though. i use it on my boat and it's good stuff. doesn't get much of the grease off, but it gets the stains off. it kind of bleaches the alloy, LOL.

if you want to get some stronger degreaser, look in the phone book under "chemicals - industrial". there should be someone who has some super strength degreaser. but you'll probably have to buy it in either 5 or 10L, and it will probably cost a fair bit, but it will be strong stuff. the sort of stuff that when it says to dillute it, you dillute it or it will eat your skin.

if it is alloy that you are cleaning, try getting some alloy cleaner. it's a chemical that you mix with water and it cleans alloy really well. don't think it does much on steel though. i use it on my boat and it's good stuff. doesn't get much of the grease off, but it gets the stains off. it kind of bleaches the alloy, LOL.

if you want to get some stronger degreaser, look in the phone book under "chemicals - industrial". there should be someone who has some super strength degreaser. but you'll probably have to buy it in either 5 or 10L, and it will probably cost a fair bit, but it will be strong stuff. the sort of stuff that when it says to dillute it, you dillute it or it will eat your skin.

sounds like alibrite or allumabrite - which is normally a sulfuric acid mix for cleaning alloy.

i've been through a few of those "industrial degreasers" which were up to $400 for 20L and the bunnings green stuff was alot better.

a can of oven cleaner will do a whole gearbox - just cannot get it on any of the plastics or rubber boots.

pretty sure the stuff i use is blitz aluminium cleaner. probably the same thing though. i just get it from supercheap for about $15 for 1L. the liquid is bright pink.

upon a bit of looking around, yeah it's the blitz stuff.

taken from the website

BLITZ ALUMINIUM CLEANER

Chemtech Blitz is a unique formulation specifically designed for the effective cleaning of any aluminium or stainless applications such as intercoolers, turbo chargers, valve covers, radiators, bull bars, dinghies, side steps in part preparation of a high gloss finish. Blitz is safer to use than products containing hydrofluoric acid.

so it can also be used on stainless

Or you could buy a pressure cleaner [karcher, spitwater etc], use the degreaser and then wash off with the karcher. A good pressure cleaner can take your skin off at 100mm, so use gloves when holding parts and getting into it.

I have a 5L bottle of Kenco cleaner, sprayed some of it on the oil stain in the garage and it took most of it off. It cleaned all of the oil and grease of my engine. Also tried the truck wash at a spray paint workshop, very strong stuff.

For grease/oil - kerosene, tho some use diesel. The water based degreasers i've used have been hopeless, but they'd probably be ok for cleaning off the kerosene.

+1 for kerosene - works great only problem is it tends to leave a slight "film" of kerosene. Pressure washer off the stuff afterward and you will be laughing.

Another thing I recommend for parts that do not get too hot is to put wax on them afterward on visual/cosmetic surfaces - don't put wax on "working"/mechanical surfaces surfaces - any gel wax would suffice - this helps dirt and other crap from sticking easily.

you use wd40 as a cleaner? umm, why not use degreaser or something like that which is actually designed to remove grease?

WD40 is a grease remover. if you have a greased joint you should NOT use WD40 on it, unless it is seized... in which case you can help anti-seize it with WD40 but you must clean the WD40 off it afterwards and re-grease the joint.

i like using R60 solvent. dries clean eats the crud away quickly tho i havent tried it with brake parts. You also have to watch as if you get dermatitis on your hands it'll make ya have a reaction

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...