Jump to content
SAU Community

Recommended Posts

When using Knock monitoring systems you need to input a frequency to monitor use this guide as a starting point. I often get called and asked what starting point to use as it is not something that is easy to find in any literature, i have put together a list of my starting points for a few different engines.

If the engine is not listed just ask and i will add it to the list (only takes a few minutes to work it out).

RB20 7.3khz

RB25 6.7khz

RB26 6.7khz

RB26 (forged) 6.6khz

RB28 6.6khz

RB30 6.7khz

RB30 (forged) 6.6khz

VG30 6.6khz

VR38 6.0khz

VR38 (4l) 6.0khz

VQ20 7.5khz

VQ30 6.2khz

VQ35 6.0khz

SR20 6.7khz

SR20 (2.2l) 6.6khz

SR20 (2.35l) 6.3khz

CA18 6.9khz

2JZ 6.7khz

2JZ (forged) 6.6khz

2JZ (3.4l) 6.6khz

1JZ 6.7khz

B16A 7.1khz

LS1 5.8khz

LS2 5.7khz

XR6T 6.2khz

XR8 (modular) 6.4khz

RB20 Forged, and RB20DE+t Forged. How do you work it out? just get it to knock at a low load with the kmon?

Slight off topic question, can you run the kmon from aux power? or will it only work from the laptop?

RB20 Forged, and RB20DE+t Forged. How do you work it out? just get it to knock at a low load with the kmon?

Slight off topic question, can you run the kmon from aux power? or will it only work from the laptop?

Its more to do with bore size, if you look @ the specs you will notice most jap 6 inline cyls are close as they all run around the 86-87mm bore.

There is much more to it than just bore size as many things can skew the optimal frequency but this guide will get you close enough.

I'm pretty sure yo could use a usb charger to run it.... i will ask ray @ gizzmo for you.

what about the frequency bandwidth? care to explain a bit about this option? what is it for what does it do?

The first post above is made to centre the frequency @ an approximate target. The bandwidth control is then used to determines how far above and below the centre frequency the device will detect, i.e. the width or spread of frequencies.

A narrow bandwidth adjustment is very specific, useful for accurately accentuating a specific knock frequency (if you know it). Narrow bandwidth adjustments tend to have less noise.

A broader bandwidth allows more frequencies to be heard, useful for a new set-up where the actual frequency is not known or for initial testing and finding the correct centre frequency. Broader adjustments tend to have more "noise".

There is no correct Bandwidth per see but the narrower the bandwidth the less feedback or noise will be recorded or heard. Nice for loose or noisy solid cammed type engines that naturally emit lots of mechanical noise.

Below is a diagram:

Yellow vertical line is the centre frequency (in this case 6khz)

Red horizontal line is narrow bandwidth

Green horizontal line is broad bandwidth

6khzbandwith.jpg

  • 2 years later...
  • 1 month later...

In addition to the above, has anyone got the kmon to log using fc datalogit? The manual didnt include the designation of the three wires ???

post on the facebook gizzmo page the owner ray will reply quite quickly, i cant remember the wiring. its just a 0-5v output.
  • 3 years later...
1 hour ago, MagicMikeZ32 said:

Surprised you don't have the formula saved on your laptop? Of course understanding this just puts you in the ballpark....

 

=900000/(3.14*0.5*bore diam)

among 1000s of others like crank degrees to ms etc... but its a 2sec reference here instead of trolling through pages of spreadsheets :P

On 07/12/2016 at 3:25 PM, 89CAL said:

HP Officejet Pro? Sounds like an awful ECU

haha but an awesome wifi printer for quick screen grabs for customers

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds good Hmm suppose the main thing is, how much do you care about this car? The filler doesn't make for a very good water barrier lol. If there was a tiny little bit of rust forming now, that in 3 to 5 years time becomes obvious under the paint (starts to bubble up), would it bother you? 
    • I already have the ability to datalog the voltage... what I can't do is correlate it to what the gauge is showing when I'm looking at the data at a later date. Or something like this. Except getting the oil to 125C+ involves me going 200+kmh at the track so you can imagine this is a little tricky unless I do something like note what the voltage is when I am at the top of 5th gear so I have a point to reference on. Drove car today. O2 still reading richer because hopefully not a leak instead of massive restriction I've introduced. Car really doesn't sound like a LS. It's quite strange. Pulled a bit of fuel out up top. This does potentially explain why my spark plugs looked like the car was running pretty over-rich. If I was tuning it to a ~12.7 which in reality was far richer than that in the past. It will be handy to have the dyno WB to compare my WB to to compare notes that's for sure. At this point I'm happy to just sit in the passenger seat and tune the thing given I've got about 7 million hours on the platform lol.
    • Yeah I understand you have to pay for an updated map or subscription service or something. But I can't even find a current map for Australia. My map is dated 2017, but didn't this car version still sell in Australia until 2021?   Also, just as an aside, the navigation system warns you of traffic incidences ahead.....why would they include that on a map they knew is not receiving live information. I am forever going to be warned of an incident that probably existed for 30 minutes 8 years ago.
    • Car has been sold and I am now selling leftover parts. Prices are non-negotiable as I will sell to my mechanic if it won't sell here. Prices are firm except for the Random Parts listed at the very bottom. All parts are genuine except for the S-Tune front bumper. Volk Racing TE37SL 19×10.5″ +12 5×114.3 pressed graphite with P-Zero 275 30 19 tyres [USED] $4,500 Wheels are in perfect condition, have been sitting in my garage for the past 6 years. Tyres still have 90% tread, but since they're now old, I would not recommend you drive hard on them. K-Sport Super Sport External Reservoir Coilovers (made to order) [NEW] $2,500 Front spring rate 14kg, Rear spring rate 7.5kg Fork Type. You can read all about it here (https://www.k-sportracing.com/product_detail.php?Key=12). I was going to start tracking the GTR, but never got around to it. Paid $3500 (after USD conversion and taxes). HKS Kansai Service Tower Bar [NEW] $500 Never fitted in the original Japanese box. R34 GTR S-Tune Fibreglass Bumper [NEW] $500 No mesh - No Box - No damage - just dusty. Nitto RB26 Clear Timing Cover [NEW] $50 Couldn't fit RB2630 due to bonnet clearance. HKS Piping Kit Special Type (BNR34) & Apexi Power Intake Air Filter Kit & Password JDM Adapter [USED] $1,000 Missing some rubber hoses and supports, but you get what you see. Nismo NE-1 Weldina Turbo Back Exhaust & Custom 3.5"straight pipe [USED] $1,000 Needs some love, but perfect for those who want to go back to OEM+. Bayside Blue Aluminium Vspec Bonnet/Hood [USED] $700 Came off my GTR. Unfortunately, the tips have been slightly ground down. It will need some repairing. Bride Low Max Super Seat Rails [USED] $350 The price is for both sides. Will post pictures when I get a chance. Random Parts [USED] - negotiable Standard rb26 cams (intake and exhaust) $10 Stock amber front indicators $10 Standard GTR bumper lower side grills $10 Stock amber side indicators $10 Nismo Sports Resetting ECU $50 Water reservoir $10 Stock airbox mouth $10 Stock fuel rail $10 Stock coilovers from R34 GTR Vspec $100 PM me which items you are interested in. I do work 9-5, so I will be responding daily at best. Best time for pick up is after 5 and before 7 on weekdays, or i can work something out on weekends. I will only accept cash or PayID. Pick up only - located Epping NSW area.
    • sensible choice....and all 32s should be in yellow
×
×
  • Create New...