Jump to content
SAU Community

Recommended Posts

I have the factory Xenon lights on my M35 and the low beam is nice. The high beam however is....underwhelming, halogen lights FTL! Has anyone put a hi lo HID kit in their car? Is it possible? What do people recommend?

Cheers

Rich

Link to comment
https://www.sau.com.au/forums/topic/329471-m35-xenon-lights/
Share on other sites

I have the factory Xenon lights on my M35 and the low beam is nice. The high beam however is....underwhelming, halogen lights FTL! Has anyone put a hi lo HID kit in their car? Is it possible? What do people recommend?

Cheers

Rich

you don't want Xenon for high beam as they are slow to come to full brightness and don't like being turned on and off to much.

+1 on what these guys have been saying. I decided to replace my shoddy highbeams with some Phillips Blue vision globes, and these are an improvement over std. Colour matches the xenons much better, light output is good for a 55/65w globe.

The other alternative is to rewire the fog/highbeam headlight circuit with some relays; (this stops you pulling too much current through the switchblock) and use higher wattage H4 globes, I've used up to 90/110w globes without issue in other cars and they are bloody amazing!

The downside of this is; higher wattage globes can melt the plastic headlight housings. So be sensible. Hope this helps.

I've used up to 90/110w globes without issue in other cars and they are bloody amazing!

The downside of this is; higher wattage globes can melt the plastic headlight housings. So be sensible. Hope this helps.

Yep, My highbeam H4's are 90/100w. Not a problem as long as they are UV treated

Yep, My highbeam H4's are 90/100w. Not a problem as long as they are UV treated

That's good to know, I erred to the side of caution, due to the cost of headlights, might go a bit harder! Did you upgrade wiring or do relays? Some cars already have them in place.

Cheers, Dale

That's good to know, I erred to the side of caution, due to the cost of headlights, might go a bit harder! Did you upgrade wiring or do relays? Some cars already have them in place.

Cheers, Dale

Nup, straight bulb replacement, nothing more required.

  • 2 weeks later...
+1 on what these guys have been saying. I decided to replace my shoddy highbeams with some Phillips Blue vision globes, and these are an improvement over std. Colour matches the xenons much better, light output is good for a 55/65w globe.

The other alternative is to rewire the fog/highbeam headlight circuit with some relays; (this stops you pulling too much current through the switchblock) and use higher wattage H4 globes, I've used up to 90/110w globes without issue in other cars and they are bloody amazing!

The downside of this is; higher wattage globes can melt the plastic headlight housings. So be sensible. Hope this helps.

Can attest to your changes. I used to run 90/130w H4 globes in my MKII Cortina with relays on low beam and high beam. I replaced the Lucas sealed beam 50/60w units with Hella H4. There was the occasional burn mark on the plastic backing but nothing too bad. Off course there was much more room for cooling compared to the Stagea. :-) I'll get around to doing the Stagea shortly. Was thinking about after market fog lights in the lower grill since the factory ones in the headlight are not great either. Any one done added without changing there front bumper?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...