Jump to content
SAU Community

Recommended Posts

stagea one is better. no cooler or should i say warmer... ideal for a relocator conversion. but the new ones are all aluminuim. early ones (one of a motor) has a steel thread.

or if you want a rb20 one is better again. but straight out of the block, not angled. new ones have a steel thread. but you have to use a toyota filter (z418) or any with a relief valve in it)

I have several laying around my shed you can have one for free if you are going to use one. They are pretty useless and you would be better off with a relocation kit and aftermarket oil cooler but as i said if you do want to use a factory one you can have one for free just pay the freight or if you are on the gold coast or brissy area just pm me and you can pick one up.

jJust to clarify when you guys say to get rid of it and fit a relocator and external cooler dont they replace just the filter and is there a housing off a different rb that still has both the pressure and temp fittings? I there any kind of aftermarket cooler that replaces just the heat exchanger part and leaves all the other bits exactly the same? Obviously you would have to jump the coolant line back into itself.

what about (factory oil coolers) my 1993 gtr has an oild cooler mounted in the front passenger side vent... is this a factory setup??

i was wondering about it???

cheers

Not factory, the factory oil cooler (oil/water heat exchanger is a more accurate description of it's function) is as what the the picture suggests, attached to the block.

Oil cooler kits found on the passenger side behind the front bumper are aftermarket ones.

The oil cooler shown above is as much an oil warmer as anything. It does very little to keep the oil cool. It is not uncommon for the part to fail also.

So the question is - is there an aftermarket part that replaces the oil cooler bracket in the diagram at the top and removes the oil cooler/warmer as fitted by Nissan?

Yeah i hear ya,

but what i mean is, alot of the Nismo equipment is offered on a new purchase.. so essentially its a"factory"option. Note the quotations.

And i dont believe there is a bolt on replacement for the factory oil warmer/cooler.

Oil cooler kits found on the passenger side behind the front bumper are aftermarket ones.

The oil cooler shown above is as much an oil warmer as anything. It does very little to keep the oil cool. It is not uncommon for the part to fail also.

So the question is - is there an aftermarket part that replaces the oil cooler bracket in the diagram at the top and removes the oil cooler/warmer as fitted by Nissan?

The RB20 doesn't have the factory oil warmer, so the taking the mount from it (housing, bracket? im not sure what the name of it is) is popular when you have an A/M oil cooler.

$120 fron nissan for a rb20 one.

unbolt your oil cooler/filter housing and bolt the 20 one in its place. use a z418 filter, not the genuine nissan 145 as you no longer have a relief valve.

(rb20 has it on the block, where as rb25/26 has that part blocked off and instead has them in the oil cooler/filter housing)

if you are using a remote filter, put the oil pressure sensor in it there, and lengthen the wiring to it. if not then use the 1/8 npt port to the rear of where the filter/cooler housing bolts on to the engine. (at about cylinder 5 along the block)

nismo has a replacement housing, but its like $1000. it has 2 -12an fittings where the cooler sits.

also nismo has a oil cooler kit, said housing, with a custom aircon condensor with a 25 row oil cooler integrated into it. i have one in my garage. i had the brocher for it but i lost it. was an option for the aussie deliverd ones.

post-19586-1279960505_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...