Jump to content
SAU Community

Recommended Posts

Hi guys,

i just wanted to know some of the best ways to maintain them with these mods below other than getting it serviced every 5000kms.

engine mods are:

-greedy boost controller (10psi)

-nismo full exhaust 3"

-k&n podfilter

-CENTRAL 20 ECU

-Greedy Front mount intercooler

Cheers!

Edited by rdirty3
Link to comment
https://www.sau.com.au/forums/topic/330515-best-ways-to-maintain-your-skyline/
Share on other sites

Dont drive it like a dick and flog the crap out of it is the first step :( Just make sure when something needs done that you do it rather than leaving it to fix later.

is there any particlar maintaince i need to take with the mods made to it?

is there any particlar maintaince i need to take with the mods made to it?

only thing that i can see is the pod will need re oiling every 10k or watever, and its spelt greddy, not greedy :(

Dont drive it like a dick and flog the crap out of it is the first step :D Just make sure when something needs done that you do it rather than leaving it to fix later.

If that's the case he would have gotten a Prius... these cars were designed to get sexy with :blink:

As for maintenance, oil/oil filter/air filter/spark plugs every 5000kms timing belt/tensions/seals every 100 000kms.. they're reliable cars that don't break with mild mods.

I've had 3x imports, I have sexy time with all of them and none of them have failed. This involved skin pad days, etc... no dramas!

you will easily get 10,000kms out of a set of copper plugs. should get 15,000kms out of them if your coilpacks aren't dead/dying. no point spending the extra money on irridiums. the set i pulled out of my 33 were dead after about 20,000kms.

oil change every 5,000km filter change +10,000km

copper spark plugs every 5,000 to 10,000 dont wast ur money with the platnem ones

dont thrash it like a dick.

timing belt every 100,000km

why not thrash it like a dick? Nissans take them like a real car, unlike Australia cars which are not really Australian

as long as it's maintained, cooled properly, they love it

getting slightly off topic now, but aussie cars will take a thrashing just as well as nissans do. look at how many junked out old vn's, etc are still going with over 300,000kms on the clock and getting thrashed by young idiots who usually do very little in the way of maintenance.

on topic though, just treat it with respect like you would any other car that you cherish. they aren't some super spectacular motor (depsite how a lot of people on this forum make them out to be). just regular servicing, not thrashing the arse out of it then pulling up straight away without letting it cool down first, use decent quality parts, etc.

I had a commo-crap vn as my very first car, and with all cars I service them very well with decent oil/filters/etc.

I can tell you this, they're shet, car had around 150xxx km on the clock and during the time I had it, I went through:

- 2x power steering pumps

- 1x CAS

- 1x Alternator

- Shift Solenoids

They're crap cars man... then I bought a 1989 180SX, which was even older than my VN and to my surprise, nothing broke, nothing gave way, all electrics worked, and even though the KMs weren't genuine (like most imports).

Yeah off topic lol..

Just remember to warm up, cool down, and regular maintenance and loads of sexy time haha :nyaanyaa:

If that's the case he would have gotten a Prius... these cars were designed to get sexy with :D

I drive my dad's Corolla harder than I do with my Skyline since you need to floor the sh*t out of the Corolla to actually get it up to speed... otherwise you get overtaken by trucks & buses :)

I had a commo-crap vn as my very first car, and with all cars I service them very well with decent oil/filters/etc.

I can tell you this, they're shet, car had around 150xxx km on the clock and during the time I had it, I went through:

- 2x power steering pumps

- 1x CAS

- 1x Alternator

- Shift Solenoids

They're crap cars man... then I bought a 1989 180SX, which was even older than my VN and to my surprise, nothing broke, nothing gave way, all electrics worked, and even though the KMs weren't genuine (like most imports).

Well I wasn't talking about reliability, I was talking about them taking a beating. But on reliability, you've owned one Holden and declare all Aussie cars to be shit? Come on...every manufacturer has their lemons. In contrast I owned a VR that only ever had a head gasket leak. Took it from 150,000-230,000km without another worry. But I wouldn't go declaring them all to be 100% sound based on my one experience! And atleast when shit goes in the Aussie cars they are much cheaper to replace than genuine items from import manufacturers.

i had an ea falcon (the worst of them) and in the 2 years i owned it i had the bonnet up less than the 18 months i owned my 33. only problem i ever had with the falcon was a head gasket and the leads needed replacing due to old age.

+1 to copper spark plugs being the way to go. had a mate recently whose iridiums lasted 3000km!

no. I used to be like u.

Copper may be a better conducter but if you want any form of longevity u need iridiums.

Coppers last aages (10000kms or wateva). But heat kills them. I actually had 2 fail, and shattered the ceramic part on 2 plugs after 1 track day (BCPR7ES's).

My mechanic also races at QR using iridiums, and they last for many meetings.

You may think they are the way to go, but we have actually seen the results.

there's plenty of testimonies in the spark plug thread going both ways. some people say their iridiums lasted just a few 10k, some have them last over 100k. A friend of mine has a soarer with a bit of extra boost, he spent many hundreds trying to find the source of a misfire which ended up being his spark plugs, he didn't check them cos they were only 3000km old. May have been a faulty plug, but there's still a fair few stories each way out there.

On a side note, Bosch platinums are less than $40 for 6. Some extra kms but without the big $$$

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...