Jump to content
SAU Community

Recommended Posts

Hi guys,

i just wanted to know some of the best ways to maintain them with these mods below other than getting it serviced every 5000kms.

engine mods are:

-greedy boost controller (10psi)

-nismo full exhaust 3"

-k&n podfilter

-CENTRAL 20 ECU

-Greedy Front mount intercooler

Cheers!

Edited by rdirty3
Link to comment
https://www.sau.com.au/forums/topic/330515-best-ways-to-maintain-your-skyline/
Share on other sites

Dont drive it like a dick and flog the crap out of it is the first step :( Just make sure when something needs done that you do it rather than leaving it to fix later.

is there any particlar maintaince i need to take with the mods made to it?

is there any particlar maintaince i need to take with the mods made to it?

only thing that i can see is the pod will need re oiling every 10k or watever, and its spelt greddy, not greedy :(

Dont drive it like a dick and flog the crap out of it is the first step :D Just make sure when something needs done that you do it rather than leaving it to fix later.

If that's the case he would have gotten a Prius... these cars were designed to get sexy with :blink:

As for maintenance, oil/oil filter/air filter/spark plugs every 5000kms timing belt/tensions/seals every 100 000kms.. they're reliable cars that don't break with mild mods.

I've had 3x imports, I have sexy time with all of them and none of them have failed. This involved skin pad days, etc... no dramas!

you will easily get 10,000kms out of a set of copper plugs. should get 15,000kms out of them if your coilpacks aren't dead/dying. no point spending the extra money on irridiums. the set i pulled out of my 33 were dead after about 20,000kms.

oil change every 5,000km filter change +10,000km

copper spark plugs every 5,000 to 10,000 dont wast ur money with the platnem ones

dont thrash it like a dick.

timing belt every 100,000km

why not thrash it like a dick? Nissans take them like a real car, unlike Australia cars which are not really Australian

as long as it's maintained, cooled properly, they love it

getting slightly off topic now, but aussie cars will take a thrashing just as well as nissans do. look at how many junked out old vn's, etc are still going with over 300,000kms on the clock and getting thrashed by young idiots who usually do very little in the way of maintenance.

on topic though, just treat it with respect like you would any other car that you cherish. they aren't some super spectacular motor (depsite how a lot of people on this forum make them out to be). just regular servicing, not thrashing the arse out of it then pulling up straight away without letting it cool down first, use decent quality parts, etc.

I had a commo-crap vn as my very first car, and with all cars I service them very well with decent oil/filters/etc.

I can tell you this, they're shet, car had around 150xxx km on the clock and during the time I had it, I went through:

- 2x power steering pumps

- 1x CAS

- 1x Alternator

- Shift Solenoids

They're crap cars man... then I bought a 1989 180SX, which was even older than my VN and to my surprise, nothing broke, nothing gave way, all electrics worked, and even though the KMs weren't genuine (like most imports).

Yeah off topic lol..

Just remember to warm up, cool down, and regular maintenance and loads of sexy time haha :nyaanyaa:

If that's the case he would have gotten a Prius... these cars were designed to get sexy with :D

I drive my dad's Corolla harder than I do with my Skyline since you need to floor the sh*t out of the Corolla to actually get it up to speed... otherwise you get overtaken by trucks & buses :)

I had a commo-crap vn as my very first car, and with all cars I service them very well with decent oil/filters/etc.

I can tell you this, they're shet, car had around 150xxx km on the clock and during the time I had it, I went through:

- 2x power steering pumps

- 1x CAS

- 1x Alternator

- Shift Solenoids

They're crap cars man... then I bought a 1989 180SX, which was even older than my VN and to my surprise, nothing broke, nothing gave way, all electrics worked, and even though the KMs weren't genuine (like most imports).

Well I wasn't talking about reliability, I was talking about them taking a beating. But on reliability, you've owned one Holden and declare all Aussie cars to be shit? Come on...every manufacturer has their lemons. In contrast I owned a VR that only ever had a head gasket leak. Took it from 150,000-230,000km without another worry. But I wouldn't go declaring them all to be 100% sound based on my one experience! And atleast when shit goes in the Aussie cars they are much cheaper to replace than genuine items from import manufacturers.

i had an ea falcon (the worst of them) and in the 2 years i owned it i had the bonnet up less than the 18 months i owned my 33. only problem i ever had with the falcon was a head gasket and the leads needed replacing due to old age.

+1 to copper spark plugs being the way to go. had a mate recently whose iridiums lasted 3000km!

no. I used to be like u.

Copper may be a better conducter but if you want any form of longevity u need iridiums.

Coppers last aages (10000kms or wateva). But heat kills them. I actually had 2 fail, and shattered the ceramic part on 2 plugs after 1 track day (BCPR7ES's).

My mechanic also races at QR using iridiums, and they last for many meetings.

You may think they are the way to go, but we have actually seen the results.

there's plenty of testimonies in the spark plug thread going both ways. some people say their iridiums lasted just a few 10k, some have them last over 100k. A friend of mine has a soarer with a bit of extra boost, he spent many hundreds trying to find the source of a misfire which ended up being his spark plugs, he didn't check them cos they were only 3000km old. May have been a faulty plug, but there's still a fair few stories each way out there.

On a side note, Bosch platinums are less than $40 for 6. Some extra kms but without the big $$$

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...