Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

help, I went to get grocerys and when I went to drive home, started the stag up,,, it idled really low and was fighting not to stall, then cleared up but wont go over like 2.3k or so,, just like its hitting limiter,, really nead help guys

AFM.

Nm35 Died Mid Flight, anyone had this? - its tricky

We don't get offended since we have been making more power for so long that we are genuinely happy every time you guys crack a little more power than stock...... :P

AFM = Air Flow Meter

MAF = Mass Air Flow

AFM = MAF

..ahem..a little more power? i think scotty and jetwreck have both achieved a bit more than a little :)

I'm surprised no-one has bitten on this comment, as I run into all the time I'll end my rant now :/

Everyone was a bit slow to bite there Bis.

Since generalisations were being thrown around I thought.....what the hey. :/

really!....thanks for that!

Sorry Jet that was being directed at whitestag's query. (I'm pretty sure you are saying derr)

lol.....I did write a couple of responses.....but there is no real come back.

Your right....heaps of parts straight off the shelf to build a decent tractor motor....sorry RB.....hey after 20-30 years of the motor being on the market getting 270 AWKW's reliably out of one of them without cracking the motor open and with the same turbo housings should be easy aye!

lol.....how did we get here from AFM :/

Edited by Jetwreck
lol.....I did write a couple of responses.....but there is no real come back.

Your right....heaps of parts straight off the shelf to build a decent tractor motor....sorry RB.....hey after 20-30 years of the motor being on the market getting 270 AWKW's reliably out of one of them without cracking the motor open and with the same turbo housings should be easy aye!

Yeah, but isn't that almost what Scotty is doing anyway?

Funny thing but AWKW and RWKW readings are almost always identical unless there is wheel spin. Sure people add 10kw or so to their figures but I take that with a grain of salt...in fact all dyno numbers as well.

The R33 is in RWKW cos it only has one diff and doesn't struggle for traction (in a straight line at least). Obviously the stagea was missing its front driveshaft for the dyno runs. It grips up fine with it back in.

all good, went over to northshore,, they checked it and replaced the MAF and all good,,, ready for some spirited driving again...

Thanks for all your help everyone.

now onto that dump pipe..

Edited by whitestag
some of the C34 guys get a little confused.....I give you a heads up as they don't quite get it :( ......our car is 98% different to the C34! So when you hear the line "Well on my C34......" more than likely they are completely wrong with the assessment!

Sorry in advance if I have offended any C34 owners :P

98% different hey?

I was going to say: "Well on my SR20......" I was right anyway, despite the fact that I own a 4 cylinder. BAHAHhahahaha.

AND it still ended up being the AFM!

98% different hey?

I was going to say: "Well on my SR20......" I was right anyway, despite the fact that I own a 4 cylinder. BAHAHhahahaha.

AND it still ended up being the AFM!

:D what error code comes up and how do you get it with your SR20!

here's one for you.....the C34 has a shit load more in common with a R33, R34 yes?....or would you say the C34 has a lot more in common with a 350Z!

and congrats on the diagnosis........your a rocket scientist aye! :)

Edited by Jetwreck

I've got the factory MIL light on the SR20 fitted to the 1600. Never use it though.

I just plug in the nistune software and it tells me the fault codes. Pretty easy and highly recommended.

C34 has a motor in the front and so does the M35. Both are made by Nissan. Both have an AFM and by the sounds of it, have a limp home mode. That's enough commonality for me :bunny:

Rocket Scientist? Nah, just willing to help a nissan brother out...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...