Jump to content
SAU Community

Recommended Posts

Guys, I want to properly learn what this is and how it relates to handling. Some context; it's often discussed that lowering a GTR too much affects the roll centre which adversely affects handling.

Can anyone explain in lay terms, or point me to something on this site or elsewhere would be a good read up on this area. Diagrams would be good too.

Lastly, I hear you can get suspension components that allow an adjustable roll centre. Can you give me some details of what these are preferably with pics / links? This would contribute to my understanding too.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/
Share on other sites

There's a bit of info in "How to Make Your Car Handle", by Fred Puhn (available at Pitstop Bookshop - http://www.pitstop.net.au/view/technical-c.../query/plu/1734). The front roll centre of the GT-R will be fairly easy to calculate, not so sure about the rear.

From the book:

(when a car is rolling in a turn) There must be some point in space about which the car body could have rotated to assume that same angle. This point can be real or imaginary, depending on the design of the car. It is called the roll centre. Height of the roll centre above the road is important and it need not be the same at the front as the back of the car
Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5385339
Share on other sites

Has anyone actually ever calculated factory GTR roll center heights, instantaneous centers, roll axis etc etc???

I can tell you that the factory front roll center of a GTR is typically 80-85mm. Lowering the car by 1 inch normally drops 12-13% off the centers height (my own R&D). So you end up with a roll center of roughly 9-10mm. Still positive but close to going negative.

Quickly showing why excessive lowering screws everything up. All those "roll center correctors" are only a part solution. If you lower a GTR by 30mm and fit a 30mm roll center corrector under the front uprights you correct the roll center by 6-7% generally. The upper arm needs to be corrected to rectify the problem properly.

Bearing in mind this all all static calculations, Roll centers have not even started to move around the car dynamicly yet, roll axis and couple are not even considered either......

Alot of people have the general oppinion that a car set-up with the rollcenter at the same height is the center of gravity should handle well. Couldnt be more wrong, a car with RC and CG at the same height WONT roll at all and will simply slide.

Normally we set a car up so the roll center is lower than the CG. For a good reason. The higher the CG is compared to the Rollcenter the more "leverage" the weight has and the more body roll you will get. This is roll couple. To smaller distance and you create an oversteering pain. To large and you have a body roller that your forever adding more spring and bar to try and correct.

Noramally by lowering roll centers you end up raising the roll couple. Typically and for simplicities sake(so many variables) by the same % you lowered the RC . So lower the RC by 10% you raise the roll couple by 10%. Inducing 10% more leverage and 10% more roll. 10% more spring is now required to get the roll back to how it was before you changed the RC. (Again its not always a linear ammount but too indepth.)

A low roll center induces body roll and vice versa for a higher RC.

If you dont move the Roll centers together it can and will introduce under and over steer.

Lower the front roll center by say 10% you have now got to increase spring rates by 10% to get back to the original ammount of body roll (assuming linear rates/RC for ease)

Lower the rear roll center by 5% and do the same with the springs.

The front of the car now has more tendancy to roll than the rear. So in a corner the front will not resist the body roll as much as the rear. The rear will take on more of the rolling forces and as a result increase its weight transfer. Leading to only one thing, oversteer.

Most people try and dial this out with roll bars a very common problem on GTR's when lowered and not set-up properly, but the solution is to fix the roll center problem you created first.

Ive been setting-up race cars and road cars for a while and have built my fair share. I have my own equipement (C weights, alligner, bump steer guages, Susprog modeling software etc etc) so I have managed to aquire a fair ammount of data and experiance with the GTR and GTS-t chassis.

Im sure someone will sit down and google search the net to blow holes in what Ive said, because someone else uses different terminology etc but there is a little of my knowledge about the concept from first hand experiance. There is little information about roll center effects and so forth so hopefully that helps

I wouldnt normally go into this kind of discussion due to the vast ammount of oppinions surrounding the topic. Every engineer or "expert" if there is such a thing has their own view.

Please do bear in mind what ive written is only just touching on the surface when it comes to geometry and RC's etc. There is FAR too much to consider in writting it down. Dynamicaly everything changes again. I spent an entire day with another forum member last weekend doing practical excersises, calculations and so forth.

If he reads this im sure he will comment on what he took away from the day.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5385972
Share on other sites

That's a good explanation on roll centres and adverse effects.

I for one would like to lower my 34 about 25mm all round, but I like the way the car handles at stock height. It seems to sit quite flat on corners on standard v spec setup. I'm just hoping that it won't be affected handling wise too much, and then have to get uprated sway bars too.

My 32GTR had camber kits, stiffer swaybars and tein ss and wasn't too low, but it was harder to setup, to actually handle mostly due to the changed suspension geometry (rollcentres). I don't want to go down this path again lol.

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5385984
Share on other sites

As soon as you lower it from standard roll centre is moved. It is not a linear scale either, lowering the car 25mm may change the position of the roll centre greater than 25mm. It is also amazing how little Japanese aftermarket "roll centre adjusters" actually do in changing the roll centre considering how expensive they are.

Brad is definitely the man on suspension, everything I have learned has been from a suspension masterclass with him!

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5386354
Share on other sites

OK, I've decided I'm never really going to understand this more than as an overall concept. I've read up and I'm slightly baffled. It is obviously a highly complex area which you need specific knowledge for and by the sounds of things a lot of practical experience too. Simply, too low is bad for GTRs - which we all know. Just need to establish ideal front and rear ride heights (355 345 FR is what I think is right for R32s and I'm not sure how much off std this is), then fiddle with

Track

Spring rates

Damper rates

Antirollbars

All of the above to be determined by above said expert.

Very grateful to you all for your input. I'd be happy to see this discussed further but am not sure that I've got anything useful to add!

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5386745
Share on other sites

+2

Brad , sent you a PM.

Would like some advice before I spend money on the wrong mods

Love the way my R33GTR handles but want to lower it without ruining the great handling

Please share the conversation if you can.

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5386748
Share on other sites

ive been msging Brad lately, definately knows wat he is talking about, biggest problem is that most people want a lowered street car that looks good but then wants race car handling, i am one of these people.

worst part before tackling these setups is having all the adjustable arms and decent coilovers(big expense).

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5386914
Share on other sites

OK, I've decided I'm never really going to understand this more than as an overall concept. I've read up and I'm slightly baffled. It is obviously a highly complex area which you need specific knowledge for and by the sounds of things a lot of practical experience too. Simply, too low is bad for GTRs - which we all know. Just need to establish ideal front and rear ride heights (355 345 FR is what I think is right for R32s and I'm not sure how much off std this is), then fiddle with

Track

Spring rates

Damper rates

Antirollbars

All of the above to be determined by above said expert.

Very grateful to you all for your input. I'd be happy to see this discussed further but am not sure that I've got anything useful to add!

it is a very indepth topic something unless your pushing a car hard and looking for the most out of is best left alone.

The heights you have mentioned are around optimal for a gtr give or take 5mm. Just be sure to set the heights with a driver in the car and an average fuel load.

Or ideally set the heights and corner weight the car at the same time. A slight varyiance in ride height is worth the trade off if it means you can balance the chassis better.

For those worried about handling effects in all honesty unless your pushing the car hard and looking for time, a 30-35mm ride height drop is aceptable 90% of the time. While it will lower the RC and change the chassis chances are you will overcome it with sway bars like 1000's of people have done before. The expense of correcting and modifying a rollcenter height and going even further into it is not really economical when you can get a good result with a well thought out set-up that to the majority of people will drive the same as a car with 100's of development hours. Developed car will be quicker but comes back to how far are you willing to go??

My sports sedan has 1000's of hours put into r&d it hasn't turned a wheel yet. There has been several incarnations of suspension and many geometry changes made. It's still not perfect and honestly I still learn more about it every day.

Your limiting factor will more so be tires etc etc before roll centers and other geometry.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5386952
Share on other sites

I for one would like to lower my 34 about 25mm all round, but I like the way the car handles at stock height.

I went through this recently with my R33 GTS-t. I'd be interested to know what the overall handling is like at standard height vs lowered slightly (~20mm).

I went king springs and bilsteins with circlip height adjustment, and I'm running it at standard height (top groove on the shocks). rear has come down 10mm the front is unchanged.

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5386986
Share on other sites

Interesting topic. Seeing as im about to align my 33 gtst this week with all new arms, can someone point to a good height for a gts25t . I think i have heard 340mm f. 350mm r, , and where is this measured from, from guard to center of hub?

http://www.skylinesaustralia.com/forums/R3...r33+ride+height

Standard height as per above. Guard to centre of hub, correct.

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5388600
Share on other sites

maybe this can help a bit

Here is a picture of close to original setup

1std.jpg

under roll condition

1std_roll.jpg

Then we lower the car 40mm and see what happens

2_40low.jpg

and make the roll

2_40low_roll.jpg

You can see that the upper-outer link probably is close to bottum out and that the rollcentre is way off, just looking

at the geometry makes it easy to understand that it needs a lower force to make it roll when susp-arms stand

angeled up right from the beginning.

Then you have to test your coilovers workingdistans without feathers to see it can move up and down as it should, not so

nice to ride with coils bottum out at bumpstops.

Maybe it looks cool with a lowered car, but its worthless without setting things up properly i think.

And this is with only 40mm lowering.

Link to comment
https://www.sau.com.au/forums/topic/331892-roll-centre/#findComment-5390060
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...