Jump to content
SAU Community

New Photos Of Slinky's Skyline

slinky-minky

By slinky-minky,
in Victoria

 Share

Recommended Posts

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

alr33x Grand Master

alr33x

Posted
Posted

springs dont do shit, they will give you basically same ride hieght but stiffer better to do it once do it right even get second hand coils if you can should be under a grand. Otherwise you'll get springs be dissapointed and go get coilovers later on

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
springs dont do shit, they will give you basically same ride hieght but stiffer better to do it once do it right even get second hand coils if you can should be under a grand. Otherwise you'll get springs be dissapointed and go get coilovers later on

Ha!

Springs can do good.

Like you said, 2nd coil overs is another option.

Find a decent set and fit them and you should be fine.

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
springs are ok, usually not without new struts as well though then ur talking cheap coilover prices.

spose could just chop springs works for the commo boys..

:blush: Rolla boys love that too, chop, weld, skidz!

You can compress the springs, they heat it up and compress it down and let it sit till it has cooled down hence it becoming lower.

Import Monster will have a 2nd hand set of coilovers and that's the proper way of doing things.

Hehe!!

slinky-minky Community Regular

slinky-minky

Posted
  • Author
Posted

Kye gave me a link to a place in Bendigo that does suspension, and they quoted me close to $700 for just the King Springs to get it down 3cm.....plus labor (That's the cheapest they have) and was over $1000 (Supply only) if I wanted the Tein S-Tech springs, asked about coil-overs and he pretty much ignored that I even spoke!

So I think I'm going to just leave her as is for now til I move to Melbourne, It's so expensive to get anything done up here.

KURAUN Grand Master

KURAUN

Posted
Posted

$700 a rip for kings springs to be supplied and installed

even $1000 for just the supply of s-tech's

id say the prices are high becuase of where your located atm, try traction tyres, centreline etc from the recommended workshops thread when you move to Melb

would be much much cheaper imo

scotty nm35 Grand Master

scotty nm35

Posted
Posted

You could get BC coilovers for not much more. :)

Benders is only an hour and a half away from Melbourne, just watch for the cops around Kyneton, they get all sooky when their missus knocks them back...

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
Kye gave me a link to a place in Bendigo that does suspension, and they quoted me close to $700 for just the King Springs to get it down 3cm.....plus labor (That's the cheapest they have) and was over $1000 (Supply only) if I wanted the Tein S-Tech springs, asked about coil-overs and he pretty much ignored that I even spoke!

So I think I'm going to just leave her as is for now til I move to Melbourne, It's so expensive to get anything done up here.

Hah!

Yeah wait till you move to Melbourne and get it done.

how far is bendigo to melbie anyway?

It is approximately 131 k's from Melbourne.

slinky-minky Community Regular

slinky-minky

Posted
  • Author
Posted

You guys know where this little hole in Victoria is quite well. I can get from Bendigo to St Albans in 1 hour 15 minutes....

Scotty- lol yeah they can be a little sooky, but Sunbury cops are bad to, when I had my BMW was getting pulled over all the time...

cop: That's a expensive car for a p plater

me: thank you

Cop: Racing wheels?

Me: There not racing wheels, Rodney Jane Racing is the brand...and they came with the car.

kyekye Enthusiast

kyekye

Posted
Posted

Woah thats way expensive for the springs! Yeah Bendigo has its downsides sometimes. Went to se suburbs to get my car resprayed. Was quoted $4500 just for the rear quarters here! And because Im a girl and have an import Ive found no one takes me seriously. If I had a commodore and wanted to cut springs and put in fully sick neons workshops would be lined up :D

alr33x Grand Master

alr33x

Posted
Posted
You guys know where this little hole in Victoria is quite well. I can get from Bendigo to St Albans in 1 hour 15 minutes....

Scotty- lol yeah they can be a little sooky, but Sunbury cops are bad to, when I had my BMW was getting pulled over all the time...

cop: That's a expensive car for a p plater

me: thank you

Cop: Racing wheels?

Me: There not racing wheels, Rodney Jane Racing is the brand...and they came with the car.

ever been on highway patrol? :P:)

slinky-minky Community Regular

slinky-minky

Posted
  • Author
Posted
Woah thats way expensive for the springs! Yeah Bendigo has its downsides sometimes. Went to se suburbs to get my car resprayed. Was quoted $4500 just for the rear quarters here! And because Im a girl and have an import Ive found no one takes me seriously. If I had a commodore and wanted to cut springs and put in fully sick neons workshops would be lined up :)

I know that feeling Kye, The guy at the tyre centre totally ignored me, and spoke to Brenton. These days I just take him with me and let him do the talking, it's much easier then being spoke to like you don't even speak English.

I get sick of the amount of "fully sick" Commodores I see in Bendigo. I'm also very tired of having burgers/drinks tossed at my car, or people shouting "Get a real car" at me.

Did you only get charged so little because you chose a basic colour?? My mums thinking about getting her Lancer re-sprayed the poor car looks pink these days.

I think I saw you on the weekend, your Skyline is a Metallic Silver R33 with a wing right??

bombtrack Experienced

bombtrack

Posted
Posted

Speak to Thuy from J-Imports about some coilovers (and anything else you may need). He has sorted many people in this club out for parts.

He should be able to find something for you from Japan or locally (new or 2nd hand) at a very reasonable price. Just let him know you're from SAU, drop a few names about the place and you're in.

I'll PM you his details.

slinky-minky Community Regular

slinky-minky

Posted
  • Author
Posted

Thanks for the help guys, much appreciated.

It's not the driving to Melb part I have a problem with cos I'm down there 3 days a week anyway, it's just that I need my car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I think in the modern era we live in, if I were converting a hydro lifter head to solid, particularly when chasing revs, I'd be seeing what I could do to use shimless buckets. Those of us with Neos usually have this persistent niggling fear of a shim getting spat out and ruining everything. Shim-over is...yucky that way. At least the Tomei kit appears to be conventional, but it would still be nice if they'd decided to go shimless.
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Ok guys thank you very much. GCG highflow it is then 🙂 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
×
×
  • Create New...