Jump to content
SAU Community

Recommended Posts

yeah its my new drift car.

its got 10:1 CR

no decompression.

when it f**ks out a piston, ill slap a 3litre bottom end in with some cheap forged pistons.

it should last for a while, its got good oil pressure and its got mega amounts of fuel going in.

The highest I ran was around 8psi, with some decent cams and a highflow turbo I think I could have pushed it a bit further. Also another thing which will be a benefit is getting some colder spark plugs...7 range.

thanks again dan...just wondering would i b able to run psi of boost more safely with forged pistons n 660cc injectors n those 7 range spark plugs...and would it also kick in around that same sorta rev range?

thank you sooo much.

If you're going to lower the compression when you put the forged pistons in, then yes you can run more boost. Guessing at the size injectors you want to put in you'll want to be chasing >18psi anyway to make use of all the extra fuel

ok sweet all ill need is forged pistons, 660cc injectors n those spark plugs n i can run that amount of boost, thats awesome...will the boost still kick in early? wat injectors would u recommend just to be able to run to about 15-16 psi safely?

Well it's more of a case of compression, there is no way that you can expect anything more than 12psi even that's with awesome cams and a great tune. Most people will be running ~8psi on 10:1 comp.

Forged pistons will drop the compression to whatever you want, but it will turn the engine effectively into a normal 25DET really, so the boost will kick in as it normally would with no advantage of high compression.

If you want to keep the high compression, take advantage of it with one of Slides highflows, run 8psi on normal 370cc injectors. It'll have awesome low-down torque and fairly respectable power.

ive got a problem with controlling boost, its running up to around 0.8 bar which is more that i want. there is a bleed valve on the wastegate line but its fully closed, i think it may be still causing a boost increase so im gonna bin it.

boost is instantaneous. i still havent hooked up the NVCS so it falls over pretty bad, and the plugs are gapped at 1.1 so it breaks down slightly, but once i overcome these probs, it will be great.

the only hole you have to drill is for the sump return fitting.

the RB25de doesnt have a oil drain from the turbine so one must be welded into the sump (unless you wanna machine the block - FLAG)

otherwise it all bolts on NO WORRIES MATE

just bolt it all on man... its a no brainer.

if anyone is planning to do this, i have the stock R33 intercooler and piping for sale atm, for $80 ono. just pm me, its all in very good condition btw.

Don't be fooled gents. its not only the compression factor, but the piston itself, the N/a pistons are not Hyperputectic. therefore, even with low boost pressures, after a while you will melt a piston.

By all means, do this upgrade! turbo is 100% better effecient power, than most other mods. But do plan to change your pistons over in the near future.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...