Jump to content
SAU Community

Hel Stainless Steel Braided Clutch Line Group Buy


Recommended Posts

  • Replies 187
  • Created
  • Last Reply

Top Posters In This Topic

Ok, the lines are getting picked up by Fedex tomorrow meaning I shall have them late next week some time.

One small hicup, the GTT lines are not yet made and will be sent seperately in a weeks time so every one doesn't have to wait. Hope that is ok.

Cheers

LINES ARE HERE!

I'll start getting them ready today and try and mail them out tomorrow before work or worst case scenario on Thursday.

LINES ARE HERE!

I'll start getting them ready today and try and mail them out tomorrow before work or worst case scenario on Thursday.

Cheers Phil

They have all been sent out today. People in QLD should probably receive them tomorrow and every where else on Monday or Tuesday.

Blazk, Pintaline and Gimps-34 I will let you guys know when the GTT clutch lines have arrived to me.

Cheers guys

is the clutch line meant to go from master to slave cylinder or master to separation box?? any problems with by-passing the separation box??

I'm not really sure on how the GTR setup works. For reference the GTST line is quite a bit longer than the GTR line.

Edited by PM-R33

Got it today with thanks mate :rant:

I'm not sure where it's meant to go.... looks too long to replace just the factory rubber line, too short to get rid of the "block"... I'm certain it will all come to light soon enough though! :P

Thanks again, great smooth GB :yes:

Too easy Ben, glad to see the QLD guys are getting them today.

Yeah I wasn't really sure on what the GTR line replaced since it was a different length than the GTST one. But I figured you GTR boys have some weird funky setup due to the AWD hence it being different :P

I think the GTST one replaces the block, but I shall soon see.

Got mine as well :D

I'm pretty sure it replaces the block, if not I'm gonna try my best to make it replace the block

Thanks again Phil. Must be hecktic at your place trying to organise all these group buys :)

Hahaha cheers guys. The people at the post office I go to always act so suspicious every time I rock up with two boxes full of express post satchels lol.

I was under the impression via the HEL website that the GTR lines were supposed to replace the whole lot, direct line from master to slave?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yes I can see how that would put you off HFM, especially with the price of good quality brake fluid. From what I understand it as you say the BM50 is the standard BMC for a R32 GTR, I must admit I would like to go far a Genuine Nissan BM57, but lack of cash prevents that at present. With the price being so close between the genuine BM50 and BM57 a BM57 New it seems a better choice as you gain that 1/16 bore size with the BM57, I would be interested in how much difference you feel with the BM57 fitted. I am going to take SteveL's advice in the short term and see how much actually comes out of that proportioning valve vent and save up for the Genuine Nissan part. Thanks for clarifying the HFM failure
    • Thanks mate. I just got the post inspection 1/2 done from state roads when the starter motor packed up, either that or the car alarm system is having trouble.  OEM part number 23300-AA112.
    • Hi, I though I was coming to an end in finding a replacement starter motor for a rb25de neo. I came across a starter motor from Taarks and a message below stating: Direct fit. 11 Tooth count. All below part numbers have been superseded to 11 teeth. Can some body shed some light on going from 8 teeth to 11 teeth apart from 36-month / 25,000 km warranty for passenger vehicles to 12 Month Warranty. Compatible with the following Nissan part numbers: 23300-20P00 23300-20P01 23300-20P05 23300-20P10 23300-20P11 23300-AA111 23300-AA112 23300-AA300 23300-08U10 23300-08U11 23300-08U15  
    • Low battery? Maybe check capacity? I know first-hand, on BMWs if your battery drops below 80% capacity, it starts causing strange issues.
    • 8.5 +37 = should fit rear, but I think it'll hit on front. What you want is low 30s/high 20's front, mid 30's rear. That 17" screenshot you posted looks good, I'd run it on my R32 (but that's long dead now). For tyre sizes, my rule of thumb is: 8': 235, 9": 255. But that's just my opinion. Nismo sizes: 18x8.5+35/18x9.5+38 is a good starting point.
×
×
  • Create New...